查询词典 be a strain

The results show that the flow stress decreases with increasing deforming temperature and increases with increasing strain rate. The flow stress of the alloy during hot compression deformation can be described by constitutive equation in hyperbolic sine function with a hot deformation activation energy of 196.27 kJ/mol. Partial recystallization takes place in the alloys deformed at a high temperature or at a low strain rate, and large number of dislocations and subgrains are observed in the alloy. The elongated grains observed in the samples coarsen with increasing temperature and decreasing strain rate. Correspondingly, the subgrain size increases and the dislocation density decreases. The main soften mechanism of the alloy transforms from dynamic recovery to dynamic recrystallization.

结果表明：Al-Cu-Mg-Ag耐热铝合金在热压缩变形中的流变应力随着温度的升高而减小，随着应变速率的增大而增大；该合金的热压缩变形流变应力行为可用双曲正弦形式的本构方程来描述，其变形激活能为196.27kJ/mol；在变形温度较高或应变速率较低的合金中发生部分再结晶，并且在合金组织中存在大量的位错和亚晶；随着温度的升高和应变速率的降低，合金中拉长的晶粒发生粗化，亚晶尺寸增大，位错密度减小，合金的主要软化机制逐步由动态回复转变为动态再结晶。

Applying integral intermediate value theorem, new effective elasticity modulus expressions were presented, which creep aging coefficient can be calculated by the creep coefficient of intermediate time of incremental time segment. Creep and shrinkage strain were treated as a kind of compulsive strain. Compulsive strain methods were used for the analysis of creep effect and shrinkage effect about concrete curved box-girder bridge.

根据积分中值定理，推导了增量时间段中点时刻徐变系数等效弹性模量的计算式；将徐变和收缩应变视为强迫应变，推导了强迫应变法计算混凝土梁桥的徐变、收缩效应的分析方法，写出了混凝土桥梁的徐变、收缩时效分析有限元列式，并将此方法应用到曲线箱梁桥的时效分析中。

By analyzing these data, it indicates that strain-rate can enhance the flow stress, while temperature will lower flow stress, and after remained in a steady state, each stress—strain curve will be parallel to the strain coordinate axis.

数据分析表明，应变率对流动应力具有强化作用，温度对流动应力具有弱化作用，稳态变形后，各应力—应变曲线都变为一条趋于与应变坐标轴平行的直线。

The plastic deformation induced due to cyclic rotation of principal stress axes alone can be in the same magnitude as that due to shear with fixed principal stress axes. 2 The volumetric strain due to shearing of cyclic rotation of principal stress axes is found to be composed of a reversible dilatancy component and an irreversible dilatancy component. The former is characterized by its reversibility and is independent of past shear history, the latter by its irreversibility increases with the increase of cycle number yet its increase rate decreases with its accumulation. 3 The obvious non-coaxiality between directions of the principal stresses and principal strain increments is found and its degree depends largely on the change of shear stress component. 4 The intermediate principal stress has considerable effects on the deformation behavior of sands in the condition of cyclic rotation of principal stress axes. The accumulation rate of the irreversible dilatancy component increases with the increase of the intermediate principal stress parameter.

具有初始各向异性的砂土在纯应力主轴循环旋转排水条件下的主要变形规律为：①纯应力主轴循环旋转可产生与应力主轴固定单调剪切处于同一数量级的塑性变形；②纯应力主轴循环旋转引起的剪切体变包含可逆性剪切体变分量和不可逆性剪切体变分量两部分，其中可逆性剪切体变分量在一周内可完全恢复，基本与应力历史无关；不可逆性剪切体变分量随循环周数的增加呈单调增加，且增加速率随其自身累积值的增大呈减小趋势；③应变增量主轴与应力主轴之间的非共轴现象显著，且在一周内具有分段性；④中主应力对应力主轴循环旋转条件下砂土的变形特性有重要影响，不可逆性剪切体变分量的累积速率随中主应力系数的增加而增加。

And by using the initial conditions as well as the end conditions, the dynamic problem is then transferred to a second kind Volterra integral equation about the function of the axial strain with respect to time which can also be solved successfully by the interpolation method. For piezoelectric and pyroelectric hollow cylinders, by following the solving procedure for elastic hollow cylinder and by using the electric boundary conditions, the dynamic problems are transferred to two Volterra integral equations about two functions of time, one is axial strain and the other is related to electric displacement, which can also be solved efficiently and quickly by employing interpolation method. The elastodynamic solutions of hollow spheres, which are made of elastic, piezoelectric and pyroelectric materials, respectively, for spherically symmetric problems are also obtained.

对于弹性空心圆柱，通过引入一特定函数将非齐次边界条件化为齐次边界条件，然后利用正交展开技术，导出关于时间函数的方程，再结合初始条件和端部边界条件，将原问题转化为关于一个时间函数的第二类Volterra积分方程，运用插值法可给出此积分方程的解；对于压电和热释电空心圆柱，利用求解弹性空心圆柱相似的方法，再结合电学边界条件，原问题转化为关于两个时间函数（轴向应变和与电位移有关的函数）的第二类Volterra积分方程组，同样可用插值法来构造相应的递推公式高效地求解此积分方程组。

Pneumoniae FH strain was cloned and the sequence was analysed by M13 DNA sequencing method. Comparing the PCR product sequcence with MP M-129 strain P1 gene, we found that there are 4 bases different. This may result from the different MP DNA templates. The maximum homology is 98.8%. The result confirmed the fidelity and specificity of the amplified target DNA segment by PCP, and suggested that two categories of MP P1 gene still exist a few differences even in the conservation region. The cloning MP DNA segment was labelled by random hexanucleotide priming, after hybridization, the probe detection was completed using an anti-digoxigenin antibody alkaline phosphatase conjugate, and the substrates 5-bromo-4-chloro-3-indolyl phosphate and nitro blue tetrazolium. This hybridization system is much superior to the radioactive probe hybridization, because it is safe, easy to handle and has no limitation of decay time. The time required for colormetic detection is also much less than the corresponding autoradiographic exposure time needed to achieve similar detection limits with 32P-labelled probes. The Dig-probes could be used repeatedly, and this made them not only much convenient to use, but also lower the cost, and worthwhile to be used popularly.

将PCR产物进行重组，并将阳性重组质粒，应用M13测序系统对产物进行DNA序列分析，并与MPM-129株P1基因核苷酸进行同源性比较，发现有4个位置的碱基发生了变化，其同源性为98.8％，证实了PCR所扩增DNA片段的准确性和特异性，同时也证实了不同MP组型的P1基因即使在保守区也存在着一定的差异，将克隆的目的DNA片段用异羟基洋地黄毒苷配基用随机引物法标记制备MP DNA探针，杂交后用碱性磷酸酶标记的抗Dig多克隆抗体与杂交体反应，再用BCIP和NBT呈色，制备MP DNA探针，鉴定所扩增片段的特异性，与同位素探针比较，Dig探针不受半衰期限制，可反复使用，而且价格低廉，值得推广使用。

A new electrostriction material strain measure method using optical lever has been proposed.Short arm senses micro strain at contact point,with the help of optical lever micro strain has been magnified to form a facula.The CCD camera samples the positions of facula and the micro displacement of contact point can be obtained.

提出利用光学杠杆测量电致伸缩材料性能的新方法，通过触点短臂传感微形变，并通过光学杠杆将微形变放大后形成光斑，利用CCD摄像头采集放大前后的光斑，通过对光斑图像进一步的处理可以得到微位移量，从而实现电致伸缩材料应变测量。

Analysis of the 16S rDNA sequence allowed strain CW-04(accession numbers: AY703033) to be classified as a representative of a new strain of the genus Desulfotomaculum, Desulfotomaculum aeronauticumd (Bacteria, Firmicutes, Clostridia, Clostridiales, Pep-tococcaceae) whose similarity is 99%.

通过16S rDNA测序以及系列比对分析：该菌属于细菌界、厚壁菌门、梭菌纲、梭菌目、蛋白胨链球菌科、脱硫肠状菌属，与该属中的种Desulfotomaculum aeronauticumd 相似性达到99%。

Gallo laboratory strain of AIDS was reported米库拉斯波Bo Weike separated, the source of its Boboweike has been vague, then simply said to be from a number of patients with mixed blood, This separation is very normal. In May 1986, Gallo laboratory in the "Science" made a correction of their May 4, 1984 posted on the "Science" on the paper, the French had mistakenly provided by the LAV strain of the photos as HTLV-3 The strain of photos.

盖洛实验室的艾滋病毒株据称是米库拉斯·波波维克分离出来的，对其来源波波维克一直含糊其词，后来干脆说是从许多患者的混合血液中分离的，这种分离方法是很不正常的。1986年5月，盖洛实验室在《科学》发了个更正，他们1984年5月4日登在《科学》上的论文中，误把法国人提供的LAV株的照片当成了HTLV-3株的照片。

Overload preventers with strain gauges The strain gauges or load cells can be built-in directly behind a deadend of a hoisting wire rope or in a yoke which is carrying wire rope sheaves, or underneath a gear-box.

配有应变仪的防过载装置把应变仪或称重传感器直接内置在提升钢丝绳的固定端后面，或内置在牵引钢丝绳的滑轮轭中，或内置在齿轮箱下面。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。