查询词典 base metal
- 与 base metal 相关的网络例句 [注：此内容来源于网络，仅供参考]
-
Our production base is located in the base metal Xiaolan, China, with advanced production technology and facilities, improved product quality inspection system.
本厂生产基地座落在中国五金基地的小榄镇，具有先进的生产工艺和设施，有完备的产品质量检测系统。
-
Fix plastics base metal base on the metope with ST4.2 screws.
用ST4.2螺丝将塑料底座和金属底座一块固定在墙面上。
-
Experiments show that many Schiff base and their complexes have good antitumor activity, the metal complexes of nitrogen mustard, however, are few.
许多Schiff base及其金属配合物亦具有良好的抗肿瘤活性，但有关氮芥的配合物研究较少。
-
This study is to investigate the high temperature hot corrosion behavior of aluminide coating and platinum-aluminide coating on Ni-base superalloy MAR-M247. On the platinum-aluminide, aluminide and the base metal, respectively, by the salt spraying method.
本文研究MAR-M247镍基超合金表面经铝化涂层或白金铝化涂层处理后，其热腐蚀效应对腐蚀速率与显微组织之影响，并藉试片质量增加量的变化评估抗热腐蚀的能力。
-
Cold lap is a condition where the weld filler metal does not properly fuse with the base metal or the previous weld pass material.
冷隔？由于熔敷金属没有很好的与母材熔合或没与前道焊缝熔合。
-
In addition to the influences of brazing temperature and the composition of filler metal, the rate of solution of base metal into molten fil...
最后，在钎焊温度下对钎缝进行了不同时间的保温处理，发现钎缝的强度和抗弯能力仅有不大程度的改善。
-
The volumetric method is also used in the measurement of the base metal and the principal elements in the high Cr cast iron and the electrooptical spectrographic method for determination of multi elements in the high Cr cast iron is established by choice of certain basic elements as the internal standard,by correction of the base spectral line and the interfered spectral line and induced correction and blank correction of the material as well as by drawing up the correction curves.
采用容量法测定高铬铸铁中基体及主要元素的含量，通过选用基体元素作内标，对谱线进行基体和干扰校正以及材质的诱导校正和空白校正，绘制校正曲线，建立了光电光谱法测定高铬铸铁中多种元素的方法。
-
In the BPW,a brazing filler metal,which has high melting point and is able to dissolve the base metal significantly,is placed between the faying surface to be joined,the assembly is heated with high frequency induction heating,and a high uniaxial pressure is applied to discharge the molten interlayer ...
BPW新工艺以熔点较高并能显著溶解母材的钎料为中间层，利用感应电源加热并施加较大的压力，挤出液态中间层及氧化膜等形成的夹杂物，最终在焊接面周边形成圆滑过渡的钎角，同时，在界面处实现洁净母材之间直接接触的固相压力焊接合。
-
Fracture Toughness of heat-affected zone is between the base metal and weld metal.
焊接热影响区的断裂韧性介于母材和焊缝金属之间。
-
Porosity can occur anywhere in the weld metal or the base metal.
气孔能在焊缝金属或母体金属中的任何地方产生。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。