查询词典 axle

Our main production: Jingjiang, Hefei, Suzhou, TCM forklift accessories such as: oil pump drive boxes, steering cylinder to enhance the cylinder, transverse cylinder, door frame, as well as enhance the cylinder assembly, steering axle and so on, see the specific Web content.

我们主要生产：靖江、合肥、苏州、TCM等叉车的配件：油泵传动箱、转向缸、提升缸、横置缸，提升缸以及门架总成、转向桥总成等等具体请见网站内容。

The yaw velocity gains of the vehicle and the relationship among the steering center position,the 2th and 3rd axle steering angle ratio and vehicle's speed are analyzed based on the zero side-slip proportional control strategy of mass center.

引言近年来，由于市场需求及高等级路面里程的增加，公路载货车及其他特种车辆的车身及其吨位越来越大，其车轴数目也相应增加，这样造成其转向以及在复杂弯道上的通过性都较小型车要困难得多，因此多轴车特别是大型多轴车向多轮转向方向发展。

Taking QY80 auto-crane's rocker mechanism of four一axle steering system asexample,this paper presents a new method which applies multibedy system Kinematics theory toanalyse mechanism's spatial motion, builds up mathematical model of optirnization for the rochermechanism of steering System, and chooses minimization adoptive random search method to developan optimization design microcomputer program,Using aboving method and program , this paper fi-nally optimlzes each design Variable, and obtains better resul...

以QY80汽车起重机四轴转向摇臂机构为例，利用多刚体系统运动学理论对机构作了空间运动分析，建立了转向摇臂机构优化设计的数学模型，并用改进了的约束随机方向搜索法编写了优化设计的微机软件，并已应用于生产实践。

Consulting the relevant information, the engine CZ4102Q made in Changzhou Diesel Engine Factory is chosen according to the full-load speed characteristic. The clutch adopts dry single-plate diaphragm spring one which is operated by hydraulic pressure system. The choices and arrangements of rear axle, steering gear, propeller shaft, differential and brake, etc is referred to the related parts on BJ1041 light truck.

发动机的选择是经查阅资料在其现有的外特性曲线上选择的常州柴油机厂CZ4102Q 发动机；离合器的改装设计选择了膜片弹簧液压式操纵机构单片干式离合器；后桥、转向器、传动轴、差速器和制动器等部件的选择和布置参照了BJ1041 轻型载货汽车的相应部件选择和布置设计。

There are six major parameters impacting vehicle handling and stability performance: the cg location, the rigidity of tyre side list, the rigidity of steering system, the steering system transmission ratio, the rear axle roll steering coefficient and the entire vehicle circling the vertical axis the rotating inertia.

对操稳性影响较大的主要有6个参数：重心位置、车轮侧偏刚度、转向系刚度、转向系传动比、后轴侧倾转向系数及整车绕垂直轴的转动惯量。

The automobile axle locking nut was split in the assembly. The fatigue cause was analyzed through macroscopic fracture, microstructure, electron probe and hardness surveys.

某公司生产的汽车半轴锁紧螺母在装配时被拧裂，用宏观断口、金相观察、电子探针及硬度测量等方法对其断裂原因进行分析。

The main products are car-axis, farm axles, axle series of spline shaft and the PCS series of crushing machine and ancillary equipment.

主要产品有汽车轴、农用车轴、工程车轴等系列花键轴及PCS系列破碎机及配套设备。

Planetary assembly consists of the planetary gears and the drive sun gear which spline connected with the axle shaft.

太阳轮为主动件，和半轴以花键连接。

This article elaborated a 12 level of rotational speed C6132 horizontal lathe headstock design process, the headstock uses to support the main axle and to cause it revolving.

本文阐述了一个12级转速的C6132卧式车床主轴箱的设计过程，主轴箱用以支撑主轴并使之旋转。

In the pump body installed a stator swing span and a swing span rotation shaft, the swing roller bearing on the stator swing span connects with an end of the stator mount, the other end of the stator mount connects with the stator; on the plunger connecting rod sliding boot installed a static pressure balance chamber, the holding rings are arranged on the two sides of the plunger connecting rod sliding boot which has a fit clearance with the holding rings; the rotor rotates the stator simultaneously via the plunger piston; the needle roller bearings are arranged on the two inner circles and fit with the port axle.

在泵体内安置有定子摆架和摆架转轴，位于定子摆架上的摆架滚子轴承与定子托架的一端配合联接，定子托架的另一端与定子相连；柱塞连杆滑靴上设有静压平衡室，柱塞连杆滑靴两侧设有保持环，柱塞连杆滑靴与保持环有一定的配合间隙；转子通过柱塞带动定子同步旋转；在转子内圆两端设有滚针轴承，滚针轴承与配流轴配合。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。