查询词典 axis

You can use a datum axis to create datum planes, to place items concentrically, or to create radial patterns.

你可以利用一个坐标片面作为你的草图的参考特征，或者是建立和定位的依据。

The model used did not allow displacements in the x-axis direction on the face of the concrete block.

所用模型不能在混凝土砌块表面x轴方向上产生偏移。

Based on the condensability of liquid,the structure used in multi-axis force sensor of underwater robot aimed at balancing hydraulic pressure was investigated and an iteration algorithm used to calculate the pressure difference between in and out of the sensor was put forward,which applied the pressure balance method of film .

以水下机器人所用多轴力传感器的压力平衡结构为研究对象，基于液体的可压缩性，提出了膜片式压力平衡传感器内外压力差的迭代算法，推导出了膜片式压力平衡法的内外压力差、额外轴向力及相关公式。

A design method of non-perpendicular pitch cone of the honing wheel is presented in this article. By adjusting the distance from the contact point of pitch cones to the axis of honing wheel, the relative velocity between pitch cones is ensured to be in the direction of the tooth trace of the gear.

提出了用于珩磨螺旋锥齿轮的非正交珩磨轮节锥面的设计方法，通过调整节锥面切点到珩磨轮轴线的距离，保证了节锥面之间的相对速度恰好沿着齿长方向。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

The bearing of planetary axis includes cone-shaped roller bearing and the needle bearing that carry cage.

行星轴的轴承包括锥形滚柱轴承和带保持架的滚针轴承。

Then, using these data tables to graph through figure guide and get single latitude positive axis conic projection figure and histogram about length distortion with latitude.

并介绍了如何利用求得的数据表使用EXCEL软件中的图表向导进行绘图，绘得正轴单纬圆锥投影图，即大地坐标的经纬网展布图及长度变形随纬度变化的关系柱状图。

Firstly, by using the function of EXCEL software and choosing the appropriate expression to calculate and get positive axis single latitude conic projection plane right-angle coordinates data table and length distortion data table about latitude.

根据实践经验，以经度97°~108°；纬度23°~34°为研究工区，用正轴切圆锥投影模型为例，介绍利用EXCEL软件中的公式对地图制图中的数据进行运算处理，求得正轴单纬圆锥投影平面直角坐标数据表，以及长度变形随纬度变化的关系数据表。

A conic section whose plane is not parallel to the axis,base,or generatrix of the intersected cone.

圆锥的一部分，其切面既不平行于轴和基面，也不平行于圆锥母线

A conic section whose plane is not parallel to the axis, base, or generatrix of the intersected ''.

圆锥的一部分，其切面既不平行于轴和''。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。