查询词典 axial

The air damping, quadrature error, parasite Coriolis force and interference from axial accelerations are also discussed.

讨论了微机械陀螺中的空气阻尼、正交误差、寄生Coriolis力以及轴向加速度干扰等问题。

A strength analysis for two axial fan impellers of model No.4 and No.5 has been carried out using a finite element method of Algor program, in which the stress and strain distribution of impellers are discussed in detail.

利用Algor程序的有限元方法，对№ 4、№ 5两个模型轴流通风机的叶轮强度进行分析，对叶轮应力和应变分布进行了详细讨论。

Each of eight adult fresh cadaver specimen of lumbarsacral segmcnts was analyzed in four states: intact, L5S1 ALIF, L5S1 ALIF fixed with pedicle screw or fixed with translaminar facets screw, test and compare its range of motion in flexion, extension, lateral bending and axial rotation.

方法］ 采用新鲜腰椎标本8具，分别于完整状态、L5S1，前路植以Cage、L5S1，前路Cage分别行椎弓根钉固定及经椎板关节突螺钉固定下，测定前屈、后伸、侧弯及扭转运动下运动范围并进行比较。

The construction principle of analytical balance style instrument about measuring the center of mass on axial direction and the adjustment method of its sensitivity are described.

本文介绍了天平式轴向质心仪的结构原理及其灵敏度的调整方法；说明了构件轴向质心位置的测量方法及其误差分析。

An iterative temperature field model of cylinder, in which the non-linear steam temperature distributed along axial direction, was got based on two-dimensional transient heat conduction differential equation. Analytical simulation demonstrates not only a rapid solution convergence but a minor error.

在二维圆筒壁非稳态导热的基础上，得到了圆筒壁内蒸汽沿轴向线性分布，随时间非线性变化的温度场迭代计算公式，并与有限元计算结果作了对比，结果表明所得模型计算精度高、计算速度快。

The axial velocity and stagnation point offset of two opposed jets coming from two asymmetric nozzles oppositely located with large separation distance were studied by using hot-wire anemometry.

采用热线风速仪对大喷嘴间距下两不对称喷嘴形成的对置撞击流的轴线速度分布和驻点偏移规律进行了实验研究。

Three cross-sections were made through crown and gingiva of the model tooth. Curve functions of axial buccal crown and gingiva contour of each section were acquired by means of curve fitting, and the angle of emergence pofile was calculated, which represents the degree of undercut.

以下颌第二前磨牙为研究对象，在牙列模型上通过牙冠部、牙龈作3个纵断面，用曲线拟和的方法得到每个断面的牙齿轴面外形及相应牙龈外形的曲线方程，以此分析两者之间的关系并计算牙冠起始外形角度，即倒凹程度的大小。

The max stress and the max radial displacement of conveyor is also proportional to the square of rotational speed. With the decrease of the blade thickness, both the stress and axial displacement of conveyor increase rapidly. The stress and radial displacement will increase with the increment of half cone angle and lead.

螺旋输送器的最大应力强度和最大径向位移均与转速近似地成二次方关系；减小叶片壁厚，沉渣对螺旋叶片作用的正压力所引起的叶片的最大轴向位移增长较快；正常工况下，螺旋输送器的最大应力强度和最大径向位移都随着半锥角和导程的增加而增大。

The tortuosity can be described by bit weight in axial direction and the angle change of drill string bynormal can be considered as the torsion angle of the borehole.

弯曲主要体现为狗腿度，挠曲就体现为井眼的扭转。这种空间挠曲和弯曲特性可以通过测量轴向不受钻压作用的下部钻具组合的变形来描述。

Third, the error of the axial acceleration and the angular acceleration are studied and formulated.

经过扩展卡尔曼滤波算法校正后，可有效地提高载体角速度的解算精度。

Summary In copyright infringement cases,if the alleged infringer uses or even plagiarizes the copyrighted works or parts thereof,which causes no substantially adverse effect on the normal exploitation of the work,nor does it inflict any substantial damages to the right owner,the de minis doctrine should be applied to exempt the liabilities of the defendant and seek the balance of interests between the right owner and the general public embodied by the copyright law.

在侵犯著作权案件中，如果被控侵权行为人虽未经著作权人的同意，使用甚至抄袭了受著作权保护的作品或作品的片段，但若情节轻微，未对该作品的正常使用产生任何实质不利的影响，亦未对权利人的权利造成实质性的损害，则应适用&不计琐细原则&，免除行为人的责任，以寻求在权利人利益与著作权法所体现的社会公共利益之间的平衡。

This new product will become our best seller.

这个新产品会成为我们最畅销的产品。