查询词典 axial tilt

To generate lift and propulsion the Lippisch Aerodyne would utilize two co-axial propellers, diverting the slipstream downwards to achieve VTOL.

产生升降机及推进该利佩什博士aerodyne将利用两个合作轴螺旋桨，分流的Slipstream向下实现垂直起降。

The most popular design methods of the axial fan are the Single Aerofoil Method and the Cascade Method.

其工程上的设计方法比较单一，普遍采用的方法是孤立叶型法和叶栅法。

1The axial evolution law on the structure and the aerodynamic characteristics of the asymmetric flows around slender bodies of revolution at incidences is summarized:whether the flow asymmetry is powerless or powerful,the flow always appears in the structure that lee-side vortices rise,and shed vortices form,and new lee-side vortices come into being alternately on opposite sides of a slender body of revolution axially from nose apex downstream to afterbody,and always induces the sectional side force of waving quasi-sinusoidally downstream axially.

1总结出细长旋成体有攻角非对称绕流流场结构和气动力特性的轴向演化规律：无论非对称性强弱，沿轴向从头部尖顶往后体，非对称绕流总是呈现为左、右两侧背涡交替从物面向上飘起、形成脱落涡、再衍生出新生背涡的流场结构，并诱导出沿轴向呈类似正弦曲线形式振荡分布的截面侧向力。

The air damping, quadrature error, parasite Coriolis force and interference from axial accelerations are also discussed.

讨论了微机械陀螺中的空气阻尼、正交误差、寄生Coriolis力以及轴向加速度干扰等问题。

A strength analysis for two axial fan impellers of model No.4 and No.5 has been carried out using a finite element method of Algor program, in which the stress and strain distribution of impellers are discussed in detail.

利用Algor程序的有限元方法，对№ 4、№ 5两个模型轴流通风机的叶轮强度进行分析，对叶轮应力和应变分布进行了详细讨论。

Each of eight adult fresh cadaver specimen of lumbarsacral segmcnts was analyzed in four states: intact, L5S1 ALIF, L5S1 ALIF fixed with pedicle screw or fixed with translaminar facets screw, test and compare its range of motion in flexion, extension, lateral bending and axial rotation.

方法］ 采用新鲜腰椎标本8具，分别于完整状态、L5S1，前路植以Cage、L5S1，前路Cage分别行椎弓根钉固定及经椎板关节突螺钉固定下，测定前屈、后伸、侧弯及扭转运动下运动范围并进行比较。

The construction principle of analytical balance style instrument about measuring the center of mass on axial direction and the adjustment method of its sensitivity are described.

本文介绍了天平式轴向质心仪的结构原理及其灵敏度的调整方法；说明了构件轴向质心位置的测量方法及其误差分析。

An iterative temperature field model of cylinder, in which the non-linear steam temperature distributed along axial direction, was got based on two-dimensional transient heat conduction differential equation. Analytical simulation demonstrates not only a rapid solution convergence but a minor error.

在二维圆筒壁非稳态导热的基础上，得到了圆筒壁内蒸汽沿轴向线性分布，随时间非线性变化的温度场迭代计算公式，并与有限元计算结果作了对比，结果表明所得模型计算精度高、计算速度快。

The axial velocity and stagnation point offset of two opposed jets coming from two asymmetric nozzles oppositely located with large separation distance were studied by using hot-wire anemometry.

采用热线风速仪对大喷嘴间距下两不对称喷嘴形成的对置撞击流的轴线速度分布和驻点偏移规律进行了实验研究。

Three cross-sections were made through crown and gingiva of the model tooth. Curve functions of axial buccal crown and gingiva contour of each section were acquired by means of curve fitting, and the angle of emergence pofile was calculated, which represents the degree of undercut.

以下颌第二前磨牙为研究对象，在牙列模型上通过牙冠部、牙龈作3个纵断面，用曲线拟和的方法得到每个断面的牙齿轴面外形及相应牙龈外形的曲线方程，以此分析两者之间的关系并计算牙冠起始外形角度，即倒凹程度的大小。

Finally it offers the analysis of the fault-tolerance system as well as its test verification.

这样，运行于空间环境中的系统的设计目标就是在保证系统实时性

However, it is still difficult to find out the real reason of the increase of the keratinized gingiva during the orthodontic extrusion whether it is due to the proliferation of the gingival tissue or to its elastic nature, that is because the proliferation of the fibroblasts as well as the connective tissue changes in volume and the intra-fibers spaces were all immeasurable in most of the studies.

然而，仍然难以找到真正的原因增加的角化牙龈在正畸挤压它是否是由于扩散的牙龈组织或其弹性性质，这是因为增殖的成纤维细胞以及作为结缔组织的变化量和内部纤维空格都是不可估量的，大多数的研究。