查询词典 axial tilt

The shear mechanisms of steel-high strength concrete short column under different failure patterns were analyzed,and related formulae for calculating shear capacity and limit value of axial compression were put forward.

分析了型钢高强混凝土短柱在不同破坏形态下的抗剪机理，提出了相应的抗剪承载力计算公式和轴压比限值。

At last, according to the analysis of theoretical study we can get the limit bearing capacity formula of the concrete filled steel tube short column subjected to axial compress.

综合以上推出的公式，得到钢管混凝土轴心受压短柱的承载力公式。

The primary objective is to study the effect of high-modulus PVA fibers on improving the seismic performance of super-high-strength concrete short column s with high axial pressure ratio.

试验旨在研究在较高轴压比条件下，高弹模PVA纤维对超高强混凝土短柱抗震延性的改善作用。

The correctness of theory analysis is proved by the test results of 5 concrete-filled double steel tubular short column specimens subjected to axial compression load.

试验结果表明，在轴心受压荷载作用下双钢管混凝土柱的受力全过程是由弹性、弹塑性以及破坏3个阶段组成的，具有很好的延性。

In this paper, the structural analysis software, RuckZuck, was used to study the effect of subsection of the temperature on the steel structure response. Mechanical parameters include axial force, shearing force, bending moment and flexibility.

本文利用结构分析软件数值模拟研究了温度分段平均处理方案对设定的非均匀温度分布的钢结构轴力、剪力、弯矩、挠度等力学参数的影响。

First, natural frequency of Euler-Bernoulli beam with elastic bearing and without the axial force is put forward. And numerical method is used to solve the equation by a program designed by the author, and the influences of shearing deformation and rotatory inertia on frequency are analyzed.

首先对不考虑轴力影响的弹性支座Euler-Bernoulli梁的固有频率进行了推导，并用自编程序进行了数值法求解，同时分析了剪切变形和转动惯量(Timoshenko梁)对频率的影响。

Finally, in order to improve the efficiency of the calculation and design, a software on finite element graphic treatment using VBA connecting Fortran program and AutoCAD 2000 is developed to make structural analysis easier than before, with which the internal forces figures (including bending moments, axial forces and shearing forces) and structural deformation figures are drawn automatically.

为提高设计计算的效率，利用VBA开发了相应的有限元图形处理软件，该软件实现了FORTRAN程序与AutoCAD的连接，利用杆系有限元程序计算得到的结果，自动绘制出内力图以及结构的变形图，图形的自动形成使得计算成果的分析工作简洁、方便。

Under spraying humidification state, the parameters of JYPW-1 spraying axial fans for textile enterprises such as flow, total pressure, efficiency, shaft power and acoustic power level changing with water-air ratio were tested, and the performance parameter curve changing with water-air ratio was obtained. The approximate formula of its pneumatic performance in different water-air ratio condition were deduced which can be referenced for of selection and project application.

在喷雾加湿工况下，对纺织空调系统所用的JYPW-1型喷雾轴流通风机的流量、全压、全压效率、轴功率和比A声级噪声等性能参数随喷淋水气比的变化进行了测试，得到了喷雾风机性能参数随水气比变化的曲线，并整理出喷雾风机在不同水气比时，其气动性能的近似计算公式，可供喷雾风机选型和工程应用时参考。

The drained behavior of Hokksund sand under low confining pressure was studied through static triaxial test, and the samples were prepared through the dry sedimentation method. The test results were corrected through the membrane effect which is often neglected under high confining pressure, the correction to axial stress for dense sample under a cell pressure of 10 kPa is equal to 12%.

采用干样沉降法制备样品，选用静三轴仪对松砂和密砂样在10kPa 至100kPa的低围压下的排水行为进行了实验研究，并对实验结果作了橡皮膜校正，在围压为10kPa的密砂实验中，轴向应力的校正值可达到12%。

Does spiral movement synchronously,a nonlinear model was established by neural networks to describe the relationship between the helical groove and the milling cutter'sprofile,and according to the helical groove axial cross section to simulate the milling cutter's profile.

加工螺旋槽时，针对铣刀刃形的设计，应用包络面原理，采用神经网络方法建立了工件螺旋槽形与铣刀刃形之间的非线性关系模型，并通过工件螺旋槽端面截形模拟仿真出铣刀回转面刃形。

Finally, the Knight strung a line between two of the monoliths and tied the horses up there.

最后，骑士们在两颗巨石之间拉了一条绳子，将他们的座骑绑在上面。

T7zN/hyS0 The island lies south by east from here.

那个岛位于此地的正南偏东方向。