查询词典 axial flow

It only took 38 months from construction preparation at the end of October, 2001 to the first unit operating on December 20, 2004, which antedated the construction time limit by 7 months. During the period, 5-month-construction period delayed was saved because of the karst geological problems of dam's partial foundation. 3 units were put into operation in 2005, especially it only took 23 days from the runner of 4# unit hoisted to put into operation. It created the wonder of installing large axial-flow feathering unit.

乐滩电站从2001年10月底开始施工准备到2004年12月20日首台机组投产发电，仅用38个月的时间，比合理工期提前了7个月，并在此期间，抢回因厂坝部份地基岩溶地质问题延误的5个月工期。2005年又实现了年内3台机组投产发电，尤其4号机组从转轮吊装到机组并网发电，仅用23天，创造了大型轴流转桨机组安装奇迹。

On the basis of literature search on erosion of axial flow fan's blade, depending on the failure mechanisms, several kinds of coatings were prepared. NiWC35, Ni60, SNi46 and SNi67 spraying and fuzing coatings were prepared by spraying and fuzing. Cermet composite coating of LX88A was prepared by arc spraying. Cermet composite coatings of conventional WC/12Co and nanostructured WC/12Co were prepared by HVOF.

本文在综合国内外关于轴流式引风机叶片冲蚀领域的研究文献的基础上，以冲蚀机理为依据，采用火焰喷熔工艺制备了NiWC35、Ni60、SNi46和SNi67喷熔层，采用电弧喷涂工艺制备了LX88A金属陶瓷复合涂层，采用HVOF工艺制备出微米WC/12Co和纳米WC/12Co金属陶瓷复合涂层。

CT-C series hot air circle oven is equipped with low noise axial flow fan and automatic temperature control system.

热风循环烘箱是干燥工程师范炳喜先生在1978年设计的国内首创产品，产品名称为CT系列热风循环烘箱，平均热效率达30%左右。

CT-C series hot air circle oven is equipped with low noise axial flow fan and automatic temperature control system.

热风回圈烘箱是乾燥工程师范炳喜先生在1978年设计的国内首创产品，产品名称为CT系列热风回圈烘箱，平均热效率达30%左右。

CT-C series hot air circle oven is equipped with low noise axial flow fanautomatic temperature control system.

热风循环烘箱是干燥工程师范炳喜先生在1978年设计的国内首创产品，产品名称为CT系列热风循环烘箱，平均热效率达30%左右。

In this article an axial-flow fans performance of a certain helicopter cooling system was tested and analyzed.

本文针对某型直升机冷却系统的轴流风机进行了详细的理论分析及试验研究。

Obviously, It has very important significance to the studies of axial-flow compressor having high performance in our country.

运用该设计体系，在压气机设计阶段，可以实现从理论上来指导叶片端弯技术的实施，这对于我国高性能压气机的研制，具有十分重要的意义。

The numerical calculation method is adopted to study the energy characteristics of axial-flow turbine.

采用数值计算方法研究轴流式水轮机的能量特性。

The results show that the numerical simulation can predict the performances of axial-flow pumps so as to provide a reference for hydraulic design.

结果表明，数值模拟可以预测轴流泵的性能，为水力设计提供参考。

The results provide references to the optimum design of an axial-flow pump assembly.

研究成果对轴流泵装置的优化水力设计，提高泵装置效率有重大意义。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。