查询词典 axial flow

The influence law of feed rate of idle roll on the quality of end face of ring,axial width spread ratio,roll force,roll moment and metal flow characteristic in cold ring rolling process has been explored through the FEM numerical simulation of the ring with rectangular cross-section based on the elastic-plastic dynamic explicit FEM under the Abaqus software environment.

基于Abaqus/Explicit提供的显式动力学有限元算法，对矩形截面环件冷辗扩进行了有限元数值模拟，揭示了芯辊进给速度对环件冷辗扩过程中环件端面质量、轴向宽展率、辗扩力、辗扩力矩以及金属流动特性的影响规律，并从金属塑性成形原理和塑性加工力学等角度对这些规律进行了合理的解释，从而获得了进给速度对冷辗扩成形的影响规律，为环件冷辗扩在实际应用中进给速度的选择提供了依据，对揭示冷辗扩成形机理也具有十分重要的意义。

At this point, if the sizes of solid particles with the liquid into balance disc constantly in front of the high-pressure area, particle size less than or equal to A as the solid particles will flow through the axial gap.

此时，若大小不一的固体颗粒随着液体不断涌向平衡盘前面的高压区，粒径小于或等于A的固体颗粒会随着液流通过轴向间隙。

First, by controlling the aqueous process parameters, such as type of bases, flow rate of air, mixing rate, acicular iron hydroxide nanoparticles with the length of less than 150nm, and the axial ratio of about 6～8 were finally synthesized.

1控制碱法制备针形铁黄的工艺参数，如碱的种类、通气量、搅拌转速等，制得针长50nm，轴比6～8的纳米粒子。

The internal-flow characteristics of the two different axial volutes were compared.

比较了这两种不同结构的蜗壳的内流特性。

Mm stalloy slitting shears unit is equipped with axial positioning device, guides and guards with flow in three dimensions, combined tension clampas well as automatic position setting technique for coiler slot.

1250mm硅钢片纵剪机组采用了圆盘剪轴向预紧力定位技术、可三维运动的导卫装置、组合式张力压板、卷取机钳口自动定位技术以及采用大型可编程控制器完成工艺联锁操作。

Under spraying humidification state, the parameters of JYPW-1 spraying axial fans for textile enterprises such as flow, total pressure, efficiency, shaft power and acoustic power level changing with water-air ratio were tested, and the performance parameter curve changing with water-air ratio was obtained. The approximate formula of its pneumatic performance in different water-air ratio condition were deduced which can be referenced for of selection and project application.

在喷雾加湿工况下，对纺织空调系统所用的JYPW-1型喷雾轴流通风机的流量、全压、全压效率、轴功率和比A声级噪声等性能参数随喷淋水气比的变化进行了测试，得到了喷雾风机性能参数随水气比变化的曲线，并整理出喷雾风机在不同水气比时，其气动性能的近似计算公式，可供喷雾风机选型和工程应用时参考。

The internal flow degenerates under off-design conditions, the backflow regions increase at the descending and outlet segments and the distribution uniformities of axial velocity drop notably at the crest and outlet crosssections of the passage.

在非设计工况下，虹吸式出水流道内部流态恶化，下降段和出口段的回流区范围增大，驼峰断面和出口断面轴向流速分布均匀度显著下降。

An axial hydraulic reaction type turbine with adjustable runner blades operated with a high flow rate.

轴流转桨式水轮机；卡普兰式水轮机转轮叶片可与导叶协联调节的轴流式水轮机。

Phase-lagged cyclic boundary condition is implemented by a novel method in conjunction with the developed sliding interface technique to accurately simulate the arbitrary pitch ratio rotor/stator interaction without any modifications of the physics of the problem. It's for the first time to compose the computational area into one structured grids including both rotor/stator of centrifugal or axial turbomachinery with arbitrary pitch ratio. This method can eliminate the iteration of boundary conditions on the sliding interface and calculate the unsteady flow within rotor and stator simultaneously.

为了能够在较小的计算区域内不改变叶型而真实地反映出任意栅距比时的内部非定常流场，并避免近似仍采用相位后滞周期性条件，结合本文发展的网格技术，给出了一种新的实施方法，首次将动、静叶片数不等的离心式/轴流式叶轮机械转子、静子计算区域组合在一套结构化计算网格中，动/静叶排间的滑移界面完全按内场处理，避免了每一时层内，滑移界面处边界条件的迭代计算；并保证了每一时层，滑移界面处流动参数的守恒特性。

After the axial profile curves of back shroud are determined, the iterative formulae for calculating the curves of front shroud of impeller are derived in such a way that the flow passage area of the impeller profile varies with the middle curve of passage L linearly.

在确定叶轮后盖板的轴面流道曲线后，从过流断面积F沿流道中线L线性变化出发，推导出前盖板曲线的离散迭代公式。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。