查询词典 axes

"Modulation Domain"is a plane domain which is consisted of frequency and time signal axes.

"调制域"是由信号的频率和时间两个轴构成的平面域。

Drawing instruments sre used to make the drawing in which the three principal axes make equal angles with the plane of projection .

它用绘图仪器绘画，三主要轴线与投影面所成的角相等。

This paper analyzed the randomness of the relative position relation between the common vertical line of the two axes of a coupling and two centers of a coupling during installing machines,and the randomness of the position of the support plane on which a machine is installed.It pointed out the errors formed by the two randomness and illustrated the faults of the four parameters system which is used in describing the shaft alignment error of a coupling by abroad technician.

分析了机器安装过程中联轴器两轴线的公垂线与联轴器中心的相对位置关系的随机性及机器地脚支承面方位的随机性，指出了两种随机性所产生的误差，说明了国外工程界在描述联轴器对中误差时所用的4参数体系存在的不足。

Point P'' is the intersection point of the concave area 11 with the cross-sectional plane of symmetry Y parallel to the reference axes y and z.

点P，为凹入区域11与平行于参考轴y和z的横截对称面Y的交点。

A plane to the triangle, triangle identified include this in two parallel axes of the smallest rectangle.

給一個平面上的三角形，找出包含此三角形且平行於兩軸的最小矩形。

The rotational inertia of an arbitrarily triangle uniform plane is calculated by a simple method. It is pointed out that principal axes can be deduced from the calculation.

摘要用一种简单的方法计算了均质的任意三角形平板刚体的转动惯量，并由此结果给出一般三角形的惯量主轴。

By Visual Basic 6.0 program, taken the distance between hole 200mm and buried depth 120～150mm as the optimization goal, the most optimum parameters range of the mechanism was obtained as follows: the initial angle between planet frame and the line formed from spraying-fertilizer needle-tip and planet wheel axle was -45°～-40°, the initial angular displacement of planet frame was 40°～50°, the distance between spraying-fertilizer needle-tip and the planetary gear axle center was 280～300mm, simultaneously, the semi-major axis of elliptic gear was 29.364mm, the teeth quantity was 23, the ratio of semi-minor axes and semi-major axis was 0.958, the radius of circular gear was 25mm.

对该机构进行运动学分析，建立了数学模型，以穴距200mm和入土深度120～150mm为寻优目标，应用Visual Basic 6.0软件编程得出满足机构运动要求的最优参数范围为：喷肥针尖和行星轮轴连线与行星架的初始夹角-45°～-40°、行星架初始角位移40°～50°、喷肥针尖与行星轮轴心距离280～300mm，此时椭圆齿轮长半轴29.364mm、齿数23、短半轴与长半轴比0.958，正圆齿轮半径25mm。

Poleaxe Specialization now also increases critical damage done by Axes and Polearms by

天赋 长柄专精除了在使用长柄和斧类武器增加暴击率1/2/3/4/5%外，还增加暴击伤害

Poleaxe Specialization now also increases the damage your critical strikes with Polearms and Axes do by 1% per point in addition to it's old effect.

长柄武器专精现在将同时增加使用长柄武器和斧类武器造成致命一击伤害的

Axe Specialization – Renamed "Poleaxe Specialization": Now increases crit chance with Axes and Polearms by

斧类武器专精-改为"长柄武器及斧专精"：增加斧类武器和长柄武器的致命一击几率

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。