查询词典 automatic calculation

Aggregation Behavior and the Hard Water Resistant Ability of Linear Alkylbenzene Sulphonate :MesoDyn Simulation and Quantum Calculation Study The quantum calculation and MesoDyn simulation were combined in this paper, the Critical Micella Concentration difference of LAS and AS was studied by the simulation, and aggregation morphology as well as aggregation behavior of linear alkylbenze sulfonate in aqueous solution was investigated by MesoDyn simulation in the presence and absence of shear.

水溶液中直链烷基苯磺酸盐的介观模拟及其抗硬水能力的量子化学计算将介观模拟和量子化学计算方法相结合，通过模拟的方法从介观角度研究了十二烷基苯磺酸盐和十二烷基磺酸盐临界聚集浓度的差异，考察了LAS水溶液体系的聚集形貌以及微相分离时发生的复杂行为。

Organization: School of Civil Engineering and Architecture, East China JiaoTong UniversityAbstract: In recent years, some project construction and design department apply the calculation method of main bridge in the calculation of skew girder bridge for convenience, which creates the project unsafety and uneconomicalness.

摘 要：近年来，一些工程施工和设计单位在对斜梁桥进行计算时，为了方便而采用正桥的计算方法，造成了工程不安全或成本上不经济的问题。

Shim current calculationWhen shim coils are excited by appropriate current, they can generate correcting magnetic field to compensate the imaging magnetic field unhomogeneity. Based on the indirect calculation method, we proposed a novel iterative optimization algorithm to calculate shim current. Because there is a direct proportion relationship between FID signal and magnetic field homogeneity, we use the intensity of FID signal as feedback information to the calculation. Shim current can be worked out in less than 3 minutes. This satisfied the requirement that active shimming should be performed in real time.

5匀场电流计算对匀场线圈施加适当的电流后才能产生校正磁场消除成像磁场的非均匀分量，本文在匀场电流间接计算方法的基础上，利用磁共振成像原理中磁场均匀性与系统FID信号强度成正比的关系提出了一种电流迭代优化算法，将系统FID信号强度的变化作为反馈信息，能够快速计算出匀场电流对成像磁场进行补偿校正，平均耗时不到三分钟，满足磁共振成像系统对有源匀场的实时性要求。

The grid is generated by Delauney method- A nodal finite volume method is used in the now calculation. The scheme for the nux calculation is vare Leer. The adaptation for the flow computations is mesh enrichment and coarsening.

网格的生成采用Delauney方法，流场的算法为节点型有限体积法，通量的计算采用Vanleer格式，自适应采用网格的增加和删减。

Design of drainage system discharges the way of draining water and the sureness of the system to include; calculation of the water force of the pipeline, mainly includes the design of the crosswise pipe slop and pipe diameter and the design of the vertical pipe diameter; the design of the way of ventilation and the calculation of the ventilative pipe; the design of the inspection shaft to choose the sewage waste water pump.

本建筑为河南省某管理局综合办公楼，对给水排水系统的要求较高。主要设计包括：给水方式的确定，竖向分区的合理划定，管材的确定，管道的水力计算，加压设备和贮水设备的选择计算。排水系统的设计主要包括：排水体制及其排水方式的确定；管道的水力计算（主要包括排水横管的坡度管径的确定，竖管管径的确定）；通气方式的确定以及通气管道的设计计算；集水坑的选择计算并由此选择潜污泵。

In this paper, mechanical analysis of over lap section of yieldable steel ribs is made. It describes how to deal with the overlap sections in calculation of internal forces in the support.It analyzes variation of shape of steel ribs and calculation of internal residual forces resulted from yielding of steel ribs. The theory for ca...

本文根据地下结构的特点，着重对可缩性金属支架的搭接段进行力学分析，并提出了在支架内力计算中搭接段的处理方法；分析了支架缩动引起的形状变化及支架由于缩动而产生的残余内力的计算，从而建立了可缩性金属支架的计算理论。

It is very important to carry out critical experiment on spent fuel for selecting calculation code packages and validating calculation methods using burnup credit technology.

开展乏燃料的临界实验非常重要，在建造乏燃料临界实验装置之前需要对其进行大量的详细的临界计算。

For a reference GFR core design, the criticality and burnup characteristics for the single assembly model and full core model were calculated through the coupling of MCNP and ORIGEN, and the differences in the calculation precision and calculation time were compared between the fine structure model and homogenized assembly model, respectively.

本工作以一气冷快堆的设计方案为研究对象，针对单组件模型和全堆芯模型，采用MCNP耦合ORIGEN的方法，计算了有关临界、燃耗过程的几个重要物理特性，比较了采用精细化结构和组件均匀化方法在计算精度、计算时间等的差别，说明了采用组件均匀化方法进行气冷快堆全堆燃耗计算的必要性和可行性。

For a reference GFR core design,the criticality and burnup characteristics for the single assembly model and full core model were calculated through the coupling of MCNP and ORIGEN,and the differences in the calculation precision and calculation time were compared between the fine structure model and homogenized assembly model,respective...

本工作以一气冷快堆的设计方案为研究对象，针对单组件模型和全堆芯模型，采用MCNP耦合ORIGEN的方法，计算了有关临界、燃耗过程的几个重要物理特性，比较了采用精细化结构和组件均匀化方法在计算精度、计算时间等的差别，说明了采用组件均匀化方法进行气冷快堆全堆燃耗计算的必要性和可行性。

The calculation method can be also used in dynamic calculation of other ship-borne weapons under the condition of the warship sway.

该方法同样适用于其他舰载武器在舰船摇摆情况下的受力分析。

Now she was hungry and angry.She began to smoulder.

现在她又饿又气，她开始流露难以抑制的怒火。

You have placed our iniquities before You, Our secret sins in the light of Your presence.

诗90：8 你将我们的罪孽摆在你面前、将我们的隐恶摆在你面光之中。