查询词典 auger feed

Pallid maggots feed up the Greater Unclean One's exposed flesh, growing into furry, thick-bodied flies that form a dark swarm around the Greater Daemon.

苍白的蛆虫在大不净者外翻的腐肉喂养下形成一层白毛，短粗的苍蝇环绕大恶魔形成黑黑的一团。

Tent caterpillars feed on cherry tree leaves.

帐篷毛虫食用樱桃树叶。

Insufficient tension draft between lap roller and feed roller.

精梳卷罗拉与给棉罗拉间的张力牵伸不足。

This positive-feed insertion system has the tension of each roller controlled by a Control Techniques Dynamics UMD servo-motor with resolver feedback to a Unidrive SP AC drive operating in servo-mode.

在这种强制进料插入式系统中，每一辊子的张力都由艾默生CT Dynamics的UMD伺服电机控制， Unidrive SP交流驱动器在伺服模式下驱动带编码器反馈伺服电机。

Functions include: Right angle and oblique trigonometry, speed and feed calculations, thread measurements, bolt hole circles, tapping drill charts, etc.

职能包括：直角和斜三角，速度和饲料计算，螺纹测量，螺栓孔各界，窃听演练图表等。

I put it in a fish tank 1.2 meter wide, and everyday I feed it small fish and shrimp .

我把它养在一个一米二宽的大鱼缸里，我天天给它喂小鱼小虾。

The paper introduces a kind of new spiral feeding equipment for boiler-front coal slurry.It adopts air feed structure and is horizontally installed around the central section of upright wall of furnace tank for boiler.The cooling seal shell and the upright wall of furnace tank are vertically connected each other.

本文介绍一种新型炉侧煤泥螺旋给料设备，它采用加风给料结构，水平安装于锅炉炉膛竖直壁中部四周，冷却密封壳体与锅炉炉膛竖直壁相互垂直联接。

Using a drum Cr18Ni9Ti furnace tank made of stainless steel cylinder, or a Cr-Mn nitrogen heat-resistant steel castings, by the end of the furnace body, bearing bearing supports, and with a motor-reducer for use furnace tank to the slow rotation, with drum parts Rotation of the tank furnace heated evenly, and the workpiece between each other without coverage phenomenon, the same color after heat treatment furnace can feed the other end to the mouth from two roller bearing.

滚筒炉罐采用1Cr18Ni9Ti不锈钢制成圆柱型，或采用铬锰氮耐热钢铸件，一端由轴承支座在炉体外支承，并采用电动机带减速机进行传用，使炉罐缓慢旋转，工件随滚筒炉罐旋转使之受热均匀，并且工件互相之间无复盖现象，热处理后色泽一致，炉罐另一端为进料口，由二只滚轮支承。

He did not found the wolf wagged its tag until the fifth day when they feed it. He knew that he had got the trust of the animal. Another three days later, the wolf could bear him close up to release her from the trap. The wolf licked his hand after got free.

一直到第五天，他去喂食时，发现母狼的尾巴有稍微摇一摇，他知道他已开始获得母狼的信任了，又过了三天，母狼才让他靠近到可以把兽夹松开，把母狼释放出来。

In this study, a commercial CAD/CAM Software is used to plan and generate the multi-axis tool path, and a table rotating/tilting type five-axis machining center is used to perform the experimental machining operation. The material of the die studied is NAK 80 die tool steel, and the geometries are modeled as concave and convex spherical surfaces. Milling parameters considered are spindle speed, feed rate, and different types of cutting tool path. The experimental results show that the surface roughness for concave spherical surface is about 0.247 μm and roundness is about 0.0283 mm and the surface roughness for convex spherical surface is about 0.250 μm and spherical roundness is about 0.0551 mm under the cutting conditions mentioned in this study.

本研究的实验方法与步骤包括利用商用CAD/CAM系统针对实验对象规划三轴/五轴同动加工路径，并经后处理程式转换，在本实验室之平台倾斜/旋转型之五轴加工机上进行实验，实验对象为NAK80模具钢材料之凹与凸球形曲面之加工，此外考虑的切削条件有主轴转速、进给速度、加工路径等，在本研究所设定之最佳切削条件下，凹球形曲面之真圆度约为0.0283 mm，粗糙度为0.247 μm，而在相同切削条件下，凸球形曲面之真圆度为0.0551 mm，粗糙度为0.250 μm。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48