查询词典 auger drill

Abstract］ objective to explore the accuracy and safety of safety drillprepared for cervical pedicle screw trajectory.methods fourteen adult cadaver specimens of cervical spine（c3～c7）with intact structures including ligaments and perivertebral muscles were reserved and used.according to the radiographic measurements,safety drill was inserted into cervical pedicle individually.the evaluation of the drill's trajectory was carried out by ct scan and three-dimension reconstruction and autopsy.results one hundred and forty drill's trajectories were made.9 holes failed with a perforation rate of 6.4%.conclusion the safety drill prepared for cervical pedicle screw hole is safe and effective and can be applied and popularized clinically.

目的 探索安全钻头应用于颈椎弓根螺钉孔道钻探的安全性与准确性。方法随机取14具福尔马林浸泡的成人颈椎标本（c3～c7），保留完整的脊柱三柱结构及相关的韧带和椎旁肌，根据影像学测量的进钉点和进钉方向，模拟颈椎后路手术过程。选用安全钻头，进行实际的颈椎弓根螺钉孔道的钻探，将孔道行ct扫描，并斜位三维重建孔道形态，并以肉眼直视观察结果为金标准，评价孔道钻探的成败。结果钻探孔道准确率89.3%（125/140），穿孔率6.4%（9/140）。结论安全钻头应用于颈椎弓根螺钉孔道钻探的安全性与准确性均较高，可以在临床上推广使用。

Rotary hammer, cordless driver drill, electric drill, marble cutter, angle grinder, trimmer, die grinder, diamond core drill, engineer drill.

1G82 电锤，充电式电钻，电钻，石材切割机，角向磨光机，修边机，电磨，金刚石钻孔机，磁座钻。

NC Drill: Numeric Control drill machine used to drill holes at exact locations of a PCB specified in NC Drill File.

数控钻孔：使用数控钻机和数控钻文件在 PCB 的准确位置钻孔。

NC Drill: Numeric Control drill machine used to drill holes at exact locations of a PCB specified in NC Drill File.

数控钻孔：使用数控钻机和数控钻文件在。

This thesis analyzes the drill grinding methods and the grinding mechanism of the novel drill, and studies how to grind the novel drill conveniently and high efficiently. Then a special drill grinder with new mechanism is developed.

分析了钻头刃磨方法和新刃形钻头的刃磨原理，研究如何方便、高效地磨出所提出的新钻型，在此基础上进行了新原理专用钻头刃磨机的研制。

Fire drill, Abandon ship drill, Emergency Steering drill, Lifeboat launching every 3 months, SOPEP drill.

船上可能被要求进行应急演习以评估船员能力。

Through the dynamic simulation test of the indoor autoclave, the law of the influence of oxygen content, drill fluid temperature, drill fluid flow velocity and the salt concentration of the drill fluid on the oxygen corrosion rate of the S135 drill pipe steel was studied separately in order to investigate the relatio...

为研究腐蚀因素与腐蚀速率的关系，通过室内高压釜动态模拟实验，分别研究了钻井液中含氧量、钻井液温度、钻井液流速和钻井液盐浓度对S135钻杆钢的氧腐蚀速率影响规律。

The results show that with the increase of drill wears, the box dimension and the information dimension as well as the correlation dimension of drilling force signals appear obviously to have the downtrends. Accordingly, this characteristic can be effectively used to realize the monitoring of drill wears.Aiming at the characteristics of the highest overlap of the feature modes in each drill wear condition, the hidden Markov model is put forward to resolve the drill wear monitoring.

针对各钻头磨损状态下特征模式高度重叠的特点，提出采用隐马尔可夫模型HMM解决钻头磨损监测的思想，对1肠IM在钻头磨损监测中的原理及实现方法进行了系统的研究，完成了基于前后向算法和Baurn一Welch算法进行模型训练和识别的具体实施步骤，建立了基于S服网络的矢量量化器，解决了钻削力特征矢量的融合与编码问题。

The key to preve n tion and reduction of the drill string failure lies in prevention.For this reaso n,in view of the different stressed characteristics of the different sections of the drill string in borehole,the research is conducted by dividing the drill st ring into four failure sections,namely,the section at the wellhead and the secti ons at the upper part,vicinity and lower part of the zero stress point,to inves tigate the essence and basic reason of the failure,and to put forward scientific and feasible preventing measures,thus,being advantageous to complete and system atic prevention and forecast of the drill string failure.

防止和减少钻具失效，关键在预防，为此，根据钻柱各部分在井内的受力特点不同将其划分为钻柱井口处、零应力点上部、零应力点附近、零应力点下部四个钻具失效段进行研究，查出其失效的实质及根本原因，提出科学可行的防范措施，有利于全面系统地预防预测钻具失效。

The main products: geological accessories; drill, drill gear; mud pump, mud pump accessories; and drill pipe, joint locks, consisting mainly of drilling materials, to pull the drill pipe, casing pliers, Bocha, consisting mainly of drilling pad fork Tools; series of geological accessories ......

主要产品：地质配件；钻机，钻机齿轮；泥浆泵，泥浆泵配件；和以钻杆，锁接头，为主的钻探材料；以钻杆钳子，套管钳子，拨叉，垫叉为主的钻探工具；等系列地质配件。。。。。。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。