查询词典 at press time

PROMESS NC assembly systems contain electronic press (also known as feeding, clothing cylinder, NC Press) torque and power module, designed to meet the "100% Precision assembly, 100% quality assurance" in the assembly At the same time to 100% of the quality inspection.

PROMESS的数控装配系统包含电子压机（又名饲服电缸、数控压机）和动力扭矩模块，其设计是为了满足在"100％精密装配，100%的质量保证"在装配的同时进行100％的质量检验。

Under the hot-press parameters including temperature 200℃, press 5-7MPa and time 15 minutes, the IB of fiberboard at 0.88g/cm3 density which was made of Liquidambar formasana wood is higher than that of Pinus khasya var.

研究了三种木材纤维不同的漆酶处理条件与纤维板物理性能之间的相关性，找出了漆酶处理木纤维的最佳处理条件为pH3.0、时间2h、温度50℃、酶用量 20u/g；在温度200℃，压力5～7MPa，时间15min的热压工艺条件下压制成密度0.88g/cm3的纤维板，枫香纤维板比思茅松纤维板的IB 强度高，IB值可达到1.26MPa。

Preparation of the cathode includes:shaping under the press of 40Mpa, sintering at 550℃for 1 hour and at 900℃for 8 hours and threading with molybdenum bar; Considering the literatures we choose CaCl2 as salt for preparation titanium. Pretreatment of salt is for 1 hour at 100℃and for 2 hours at 300℃. Partial pressure of oxygen which need lower than 5.11×10-7Pa to reduct titanium oxides and hygroscopic property of salt need a sealed equipment to electrolyse. And finally successfully designed a satisfied one and the results show that the equipment can be satisfied the requirment of the experiment. Flow of the inert gas is 1.5L/min, the voltage is 2.8 V, temperature is 850℃and time is 2 hours during pre-electrolysis. Flow of the inert gas is 0.2L/min, the voltage is 3.1 V, temperature is 900℃and time changes with the mass of TiO2 during electrolysis, namely the greater need the longer time; To eliminate influence of salt and other impurities, the products need to wash with distilled water and dilute chlorhydric acid , then wash with dilute hydrochloric acid under supersonic wave assistant. Finally, electrometical properties of the electrolysis of TiO2 is researched by cyclic voltammetry and chronoamperometry, and results show that there are two main reodox steps, namely from TiO2 to TiO and from TiO to Ti.

阴极制备主要包括40MPa压力下模压成型、两段式烧结(1小时内升至550℃保温1小时，再1小时升温至900℃保温8小时)及烧结后TiO2块打孔用钼棒串接三个主要环节；实验中选用CaCl2作为电解熔盐，并对其进行预处理(100℃，保温1小时； 300℃，保温2小时)；经热力学计算，还原钛氧化物的氧分压至少要低于5.11×10-7Pa，结合电解过程中所用熔盐CaCl2有极强的吸水性的特点，电解装置应有较高的密封性，自行设计了一套密封性可靠的电解装置，便于实验过程中熔盐预处理和氧分压的控制；通过干燥处理预电解过程中Ar流量大约为1.5L/min、电压为2.8 V、温度为850℃、时间为2小时，电解过程中Ar流量大约为0.2L/min、电压为3.1V、温度为900℃，实验结果表明电解时间与TiO2质量密切相关，质量越大需要电解的时间越长；通过自来水冲洗—稀盐酸浸泡、洗涤—在超声波辅助作用下稀盐酸洗涤，可减少熔盐及其它杂质对电解产物检测结果的影响；最后，通过循环伏安法、计时电流法对电解机理的研究，确定电解还原TiO2制备金属钛主要经历了TiO2-TiO-Ti的过程。

The multi- connecting rods press is one kind new press which taking the multi- linkmotion gear as the operating mechanism.The slide has the obviously comes back promptly kinematics the characteristic.In work sector,The slide"s speed is steady, and is lower than the crank press greatly, this is advantageous to enhance quality of the big distorts stretch. At the same time it reduces the impact between the molds and lengthen the mold"s service life.

多连杆压力机是一种以多连杆机构为工作机构的新型压力机，滑块具有明显的急回运动特性，在工作区间，滑块速度平稳，并且大大低于曲柄压力机，这有利于提高变形较大的拉伸件的质量，同时减少模具间的冲击，延长模具使用寿命。

At the time of going to press MrWen was the only non-American among the top ten.

截至发稿前，温是前十名中唯一一位美国以外的政治名人。

In L.A., people's publicists package them with other people to create the appearance of a relationship -- they call the press and say,'Be outside this restaurant at this time and you'll see this actor and that actress, and they're together.

在洛杉矶，演员的公共宣传员会把他们和别人拉到一起以刻意制造某种关系的表象——他们打电话通知媒体说，'现在这个饭店外面你们能看到这个男演员和那个女演员，他们在一起。

The article detailed summarizes all sorts of basic constructions, action principles and presently improved conditions of center mechanisms used in tire shaping and curing press in addition, it briefly sums up these mechanisms′developed status inland at present time.

较为详细地综述了用在轮胎定型硫化机中的各种中心机构的基本结构、工作原理以及现有的改进情况，述及了这些中心机构在国内的开发简况。

Because the lock dead of the tire is the result that the car of system friction of motive and tire and ground compare, also be say that the car march forward whether a tire lock die or not of extreme limit is would with the condition that the characteristic, road of the tire face, position the angle, to press, hang the characteristic but" at any time different" of mourn the system.

由于轮胎的锁死是剎车制动力和轮胎与地面的摩擦力比较的结果，也就是说车子行进间轮胎锁死与否的极限是会随轮胎本身的特性、路面的状况、定位角度、胎压、悬吊系统的特性而『随时不同』。

The third key-press is regarded as letter affirmance key-press on mini key-board, at the same time, identifies sound, the identical method is: identifying the three sounds by lengthways three lists, identifying the three rhymes by transverse three rows, the intersectant is the whole identifying key-press of sound.

小键盘以输入第三键作为字符确认键，同时识别声韵，识别方法是：以纵向三列键识别三声；横向三排键识别三韵，纵横交合键位就是该音节的声韵全识别键。

The school is never named in the novel, but a host of clues (most tellingly the school motto ) reveals the school to be Sutcliffe's alma mater , Haberdashers' Aske's Boys' School , a fact that was picked up at the time by the British broadsheet press.

这所学校从未透露过的小说，而是一个线索主机揭示了学校的萨克利夫的母校， Haberdashers 的 Aske 的男书院，一个被选为在英国大报的时间事实新闻。

The absorption and distribution of chromium were studied in ryeusing nutrient culture technique and pot experiment.

采用不同浓度K2CrO4(0，0.4，0.8和1.2 mmol/L)的Hoagland营养液处理黑麦幼苗，测定铬在黑麦体内的亚细胞分布、铬化学形态及不同部位的积累。

By analyzing theory foundation of mathematical morphology in the digital image processing, researching morphology arithmetic of the binary Image, discussing two basic forms for the least structure element: dilation and erosion.

通过分析数学形态学在图像中的理论基础，研究二值图像的形态分析算法，探讨最小结构元素的两种基本形态：膨胀和腐蚀；分析了数学形态学复杂算法的基本原理，把数学形态学的部分并行处理理念引入到家实际应用中。