英语人>网络例句>ash 相关的网络例句
ash相关的网络例句
与 ash 相关的网络例句 [注:此内容来源于网络,仅供参考]

The effect of char on the melting characteristics of coal ash was studied in the argon atmosphere using an ash fusion determinator connected with a camera and a computer.

采用连有电脑-摄像头的煤灰熔融特性测定装置,在Ar气氛下研究了灰中焦对煤灰熔融特性的影响。

This paper also analyzes the ash wear mechanism,and then does the effects of low temperature economizer wear five factors: the first is the smoke corridor caused by wear mechanism,the second is the impact on the wall material,and the third is that of flying ash concentratio.

分析了飞灰磨损的机理,然后分析了影响低温省煤器磨损的5种因素,一是烟气走廊引起磨损的机理;二是管壁材料的影响;三是飞灰浓度的影响;四是过量空气系数的影响;五是烟气成分的变化对磨损的影响。

On heat-transfer analysis, the focus is on the analysis of the effect of heat-transfer mechanism, ash and thermal equilibrium and ash concentration on heat transfer.

在传热分析中,着重分析了传热机理,灰、热平衡及灰浓度对传热的影响。

The fly ash-based adsorbent with high crystallization and purity were synthesized by automation transformation of fly ash in vapor phase of ethylamine and water under the temperature range of 3730K to 4000K.

以电厂的废弃物粉煤灰为原料,研究了373~400K温度范围内,粉煤灰在乙胺和水的蒸汽相中自转变合成了纯度、结晶度均较高的粉煤灰吸附剂的过程。

Firstly, the fly ash is separated into three parts according to its mineralogical composition, they are ferruginous spheres, mullite-corundum and glass phases. Secondly, the contents of these elements of the original fly ash, the ferruginous spheres and the mullite-corundum are determined by chemical analysis and ICP-MS, respectively, and thus the element contents in the glass phase can be obtained by calculation.

首先根据高铝粉煤灰的物相组成特点采用新的分离方法将之分离为三个相:铁质微珠、莫来石-刚玉相以及玻璃相;然后分别用化学分析和ICP-MS测试主微量元素在高铝粉煤灰、铁质微珠以及莫来石-刚玉相中的含量,并结合相关数据计算出这些元素在玻璃相中的含量。

The mineral composition of typical coal combustion residues in China, including fly ash, bottom ash, slagging and fouling, were investigated by X-ray diffraction, Missbauer spectroscopy and scanning electron microscopy. According to the chemical composition, coal combustion residues can be divided into aluminosilicate, ferruginous and calcareous groups.

利用X射线衍射、穆斯堡尔谱与扫描电子显微镜等方法研究中国典型燃煤煤种的燃烧产物的矿物学特征,揭示出不同化学成分以及不同类型产物中矿物组成的差异性。

Because of no measures to resist floating in design,a power plant ash pond floated and inclined with the groundwater flotage after construction,which have influenced the normal use of the ash pond.

某发电厂沉渣池由于设计时没有考虑抗浮措施,施工完成后,池体在地下水浮力的作用下上浮倾斜,严重影响池的正常使用。

The company take full advantage of its rich fly ash, steam, electricity and other resources, mainly the production of fly ash aerated concrete block series of new wall materials, products with light weight (equivalent to the red brick of the 1 / 3), noise insulation good, fire prevention, good processability, energy conservation (because of light weight thermal insulation of buildings can reduce the quality and reduce air-conditioning heating) and environmental protection advantages.

该公司充分利用其丰富的粉煤灰、蒸气、电等资源,主要生产粉煤灰加气混凝土砌块等系列新型墙材,产品具有重量轻(相当于红砖的1/3)、保温隔音性好、防火、可加工性好、节能(由于质轻保温可降低建筑物质量和减少空调暖气)环保等优点。

The main multi-functional, can produce concrete block, fly ash blocks (slag and fly ash content can reach 80%), powder block, block construction waste, garbage blocks, steel block, Gangue blocks, planting grass bricks, slabs of highway slope protection, color chain block the road blocks.

主体多功能,可生产混凝土砌块、粉煤灰砌块(粉煤灰及炉渣含量可以达到80%)、石粉砌块、建筑垃圾砌块、生活垃圾砌块、钢渣砌块、煤矸石砌块、植草砖、高速公路护坡砖、彩色马路连锁砌块砖等。

Based on analyzing the fixed value of the coal ash fusibility standard substance,the uncertainty about the standard value of the coal ash fusibility standard substance was analyzed and quantitated in this paper.

通过对煤灰熔融性标准物质定值的分析,分析和量化了煤灰熔融性标准物质标准值的不确定度。

第8/191页 首页 < ... 4 5 6 7 8 9 10 11 12 ... > 尾页
相关中文对照歌词
Ash And Ember
The Ashgrove
Sinkemlow
The Memory Remains
Blunt Ashes
The Pledge (Remix)
Skin To Bone
Ash
Horizons
I Choose You To Die
推荐网络例句

Based on the relationship and the phenomenon model, an improved model of MR damper has been presented in this paper.

摘 要:本文在实验数据的基础上建立了磁流变阻尼器输出力与不同常电流控制量的关系,对现有的 p模型进行了改进。

I don't think our founding fathers were very fuckable.

我认为我们的开国元老没什么吸引力

In chapter 3, an optimum method of milling parameter based on orthogonal cutting finite element model is proposed.

第三章提出了基于正交切削加工有限元模型的铣削参数优化方法。