查询词典 arc welding

The experimental results show that with given two-wire submerged arc welding process, the low temperature toughness of the steel welds is good and the joint of medium thickness steel plant with twin-wire submerged arc welded technics can be used without heat treatment after welding.

该钢种中等厚度双丝埋弧焊焊接接头可以在不进行焊后热处理的情况下使用。

This article describes briefly process procedure and characters of 5 sets rolling tack welders for longitudinal submerged arc welding pipe unit,and introduces common defects during tack welding operation,such as air pocket,slag,arc burn,offset and misalignment etc.

简述了直缝埋弧焊管机组中五组压辊式预焊机的工艺过程及特点，介绍了预焊作业中常见的气孔、夹渣、烧穿、错边、焊偏等缺陷。

In this system we developed, according to spectrum of arc light and the relationship between arc, welding current and radiation, corresponding filter system is applied to filter ultraviolet radiation and part of visible light from arc light.

在系统中，鉴于弧光的光谱信息及其与焊接电流及电弧区国辐射之间的关系，采用了相应的滤光系统将强烈的紫外及部分可见光滤除，并将余留的光作为光源，通过CCD摄像机拍摄到了较稳定的近缝区图像。

The results established the applied basis of arc light sensing and complemented the field of welding arc physics of arc light.

在对弧光传感机理进行分析的基础上，首次将这种传感方法系统地应用到焊接过程的传感中，并利用光谱分析结果提高信号质量。

In addition, the effects of current, cathode cone angle and arc length on the current density and arc pressure distribution at anode surface in GTA welding are analyzed by the use of the built arc model, and the computed results agree well with the experimental results.

另外，运用建立的电弧数学模型，分析了焊接规范参数变化对直流GTAW电弧阳极表面电流密度和电弧压力径向分布规律的影响，计算结果与实验结论基本一致。

It is the first time that no additional anode was adopted in the magnetic macroparticles filter. At the same time the auto-re-igniting system was designed for vacuum cathodic arc deposition instrument. It ignites the arc with an electronic component with high voltage and can auto distinguish weather the arc dies out or is on during the deposition via a main power supply feedback unit. The energy for igniting the arc is very less and thus can successfully prevent the film being contaminated.

设计制造的电子式真空阴极弧离子镀引弧器成功地实现了高压脉冲引弧，可以多次重复使用，所用能量较小，可以有效防止对所镀膜的污染，引弧可靠，能够自动识别电弧是否引燃，能够在熄弧后自动重新引弧，重新引弧的速度快，有效防止了熄弧引起的气压波动，使镀膜过程中气压非常稳定。

According to spectral characteristics of the HCVAW arc in a body, energy factor which value equals to the ratio of two spectral lines' intensity, was defined.When τ's value was less than 0.1, the HCVAW arc was exhibitive of diffusedshape with lower energy density instinct; and when τ's value was higher than 0.5,the arc was a fine-constricted arc with higher energy density.

从积聚态电弧的谱线空间分布来看，阳极材料为水冷铜板时，自空心阴极端面到阳极工件，氩原子谱线相对辐射强度具有比氩一次离子谱线相对辐射强度更快的减弱趋势，最大辐射强度均出现在距空心阴极端面2mm左右的位置。

The characteristic of primary arc is analyzed, and the dynamic model of primary arc is established. The line differential equation including primary arc voltage is constructed, and the parameter estimation technique is used to estimate the voltage amplitude of primary arc, so as to determine the fault type and realize adaptive three-pole-autoreclosure.

分析了一次电弧的特点，建立了一次电弧的动态模型，利用一次电弧的特点建立了包含电弧电压的超高压输电线路相间短路的线路微分方程，通过参数估计的方法求得故障点的电弧电压，以判断故障类型，实现自适应三相重合闸。

In the proposed formulation, the fluid jump arc of Second order Fluid Stochastic Petri nets, which takes deterministic jump height, is introduced for the sake of modeling impulse rewards. In order to model non-Markovian stochastic systems, the fluid jump arc is combined with the flush-out arc. As a result the fluid jump arc as a modeling primitive has the function of emptying in zero time the existing fluid from the continuous place connected with it.

为方便利用该机制建模冲量回报，引入二阶流体随机 Petri 网中的流体跳跃弧，跳跃弧的跳跃高度取确定值；为方便建模非马尔科夫随机系统，将清空弧与流体跳跃弧结合，使得流体跳跃弧作为建模原语直接具有瞬间内清空与之相联接的连续库所的功能。

Plasma cutting machine work, the first plasma arc ignition by high-frequency oscillator excited between the electrode and the inner wall of the gas nozzle, resulting in high-frequency discharge, the gas ionization and the formation of local small arc, this small arc by the compressed air role, from the nozzle to ignite plasmon in the arc, spark generator, which is the main task.

等离子切割机工作时，首先要引燃等离子弧，由高频振荡器激发电极与喷嘴内壁之间的气体，产生高频放电，使气体局部电离而形成小弧，这一小弧受压缩空气的作用，从喷嘴喷出以引燃等离于弧，这是火花发生器主要的任务。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48