查询词典 arc process

The basic idea is that using the "point" function of software UTHSCSA Imagetool to acquire the pixel values of the event in the scanned chart image and then process these arc-shaped isochronal data with algorithms proposed by us to render these data.

基本方法是利用图象软件Imagetool中的"Point"功能获取小气候自记图图象上的记录曲线上点的像素值，然后通过我们给出的算法转换成相应的数据资料。

In the program the Newton-Raphson's method is used to iterative computation; and the method of either the cylinder-arc-length or the minimum residual displacement is adopted to control the iterative process.

在分析非线性静力和动力有限元计算方法的基础上，本文采用修正的Newton-Raphson方法进行迭代计算，并采用柱面弧长法和最小残余位移法控制迭代过程，编制了一个适合于杆件体系结构的有限元分析程序，结构可以按桁架、刚架或梁杆组合体系分析。

The results showed that the fracture toughness of the weld of HFW pipe was lowest.The value of absorbed energy of HFW weld was closely related to the heat treatment process.But the fracture toughness of fusion zone of submerged-arc welded jointer,its microstructure was coarse granular bainite,and was lower than the other locations of heat affected zone;and with the increasing of steel strength,the effect of welding heat cycles on the pipeline steel became stronger,and form coarse microstructure in fusion zone leading to decrease fracture toughness.

结果表明，高钢级管线钢高频焊接焊缝处的断裂韧性最低，其冲击功大小与热处理工艺密切相关；而埋弧焊接热影响区断裂韧性在熔合线处最低，其主要原因是此处的组织为粗大的粒状贝氏体，而且强度越高焊接热循环对管线钢的作用越强，在熔合线附近更容易产生粗大组织，使断裂韧性降低。

So, the approximate calculating formula of parabola and the length of ellipse arc is developed by the method of finding experience formula from point of view of simplifying the calculating process and getting certain accura...

本文从既能简化计算又能达到一定精度的设想，通过找经验公式的方法给出了计算机抛物线及椭圆弧长的近似公式，并给出了常用区间上计算抛物线和椭圆弧长的一次式和二次式。

Even when the distance between the welding torch muzzle and the surface of the work piece changes, this control system will keep the stability of arc length, so as to achieve a stable welding process.

该系统能够在焊枪喷嘴和工件表面的距离发生变化时，保持电弧弧长一定，从而保证焊接过程的稳定。

The manufacturing process of foaming mould of an oil pump body by using LOM prototype,electroforming and wire-arc spraying was introduced in detail.

以制造泵体发泡模具为例，详细介绍了在LOM原型的基础上，通过LOM原型的预处理、电铸和电弧喷涂等工艺手段快速制造发泡模具的过程。

Ome of this is the natural arc of a huge, fast-growing country in the process of modernization. The U.S. in the late 19th century was nothing if not what Intel's Maloney would call an IMBY country.

这是快速增长的国家的现代化进程中一个高峰。19世纪末美国如非如英特尔马洛尼所说的发起了全国动员，否则会是不足为取。

Simultaneously, It is found that modeling and simulation is the effective method understanding microscopic process of vacuum arc.

同时，可以发现，建模与仿真是理解真空电弧微观过程的一种有效方法。

During the process from continental margin rifting to ocean spreading and the thrusting of island arc, ophiolite suites and massive sulfide deposits were formed.

由宋叔和先生开创的西北海相火山岩及其黄铁矿型矿床的地质研究事业，在近半个世纪以来有了很大的进步。

The method of reading the line, arc, spine, tolerances, surface roughness and full messages of the part from DXF file generated by AutoCAD is mainly introduced. Based on the study of DXF, a program interface is developed, by which the data can be shared among different CAD systems. According to the different Characters, the respective tool paths are designed. And by a machine configure file, the General postposition process is deal with. On the research of thegeneral simulation technology that is based on the NC codes. By analyzing the characteristics of the CNC system and the NC codes, a set of general simulation interface is developed.

本文主要介绍如何从AutoCAD生成的DXF文件中读取直线、圆弧、样条曲线、尺寸公差、表面粗糙度等信息及零件的全局信息，结合回转体零件的特点，通过对应用广泛的DXF的深入分析，建立了与不同CAD系统实现数据共享的编程接口；根据零件的不同加工特征提出了相应的走刀路线，并通过机床配置文件，初步实现了通用后置处理；研究了数控系统和NC代码的特点，建立了仿真通用接口，并提出代码翻译地基本思路。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。