查询词典 arc process

After having compared the cupola furnace with electric arc furnace on the characteristics of the process of producing spheroidal graphite cast iron steel ingot module and their application effects, the results show that it will prolong the life of steel ingot module and improve the quality of steel ingot by applying arc furnace to melt spheroidal graphite cast iron steel ingot module.

电弧炉技术在球墨铸铁钢锭模生产上的应用赵海兵任元和李梅曹志张涛摘要将冲天炉和电弧炉这两种生产球墨铸铁钢锭模的工艺特点及应用效果进行对比，结果表明，采用电弧炉冶炼球墨铸铁钢锭模能够提高钢锭模使用寿命，改善钢锭质量。关键词球墨铸铁模耗A

A comparative study of porosity, oxide coontents, bond strength and wear resistance of 3Cr13 stainless steel coatings deposited by high velocity and regular arc spray processes was carried out. An orthogonal and rotational regression experimental method and an ordinary single-factor experimental method were adopted to evaluate the coating hardness with respect to the effect of processing parameters. The quantitative formula of processing patameters with coating hardness was obtained by means of microcomputer.The results show that, compared with the regular arc spray process, a dense?

对比研究了3Cr13不锈钢高速电弧喷涂涂层和普通电弧喷涂涂层的孔隙率、氧化物含量、涂层结合强度和滑动磨损性能，并采用多因素正交旋转回归设计和单因素对比试验的方法研究了高速电弧喷涂工艺参数对3Cr13不锈钢涂层显微硬度的影响，用微机回归得到了喷涂工艺参数与涂层硬度之间的定量关系式。

Coating with lower porosity, higher bond strength and hhigher oxide?contents were produced by a newly developed high velocity arc wire spray process.The bond strength in higher than 40MPa, which is increased by 52 percent than that of regular arc sprayed coatings.

结果表明，和普通电弧喷涂涂层相比，高速电弧喷涂涂层组织致密、孔隙率低、涂层氧化物含量增多，涂层-基体界面结合强度大于40MPa，比普通电弧喷涂提高了52％。

During the interruptering circuit process of MCCB, two phenomena exist: electric arc back strike and arc restrike.

在塑壳断路器开断过程中存在着两种现象，电弧背后转移和过零重燃现象，这两种现象都影响着断路器的开断过程，并且都与灭弧室内电场分布有关。

The effects of arc unstable, arc characteristics and commutating circuit parameters on the process of self-excited oscillation in current commutation are discussed in detail.

理论分析和模拟计算的结果说明了不同的开断装置电弧特性和转移回路参数对自激振荡过程的作用，为高压直流断路器转移回路的参数设计提供了有效的分析和计算工具。

The structural features and functions of V-type drafting system on spinning frame arc analyzed, Based on production practice and comparative tests, some important parameters of drafting process arc optimized.

分析了细纱机V型牵伸的结构特点和作用，通过生产实践和对比试验，优选了部分重要牵伸工艺参数，得出V型牵伸的后区牵伸倍数仍需偏小掌握的结论，并分析了其理论依据。

In this model the fuse is simulated by a time variable nonlinear resistor combined with a switch, the nonlinear resistor represented the fore-arc resistor during fusing process, the switch is used to control the cut off time, and both of the above is calculated by the ANSYS. Compared the real assay curve and the simulation wave we found that: the calculated overvoltage amplitude value is accuracy with error less than 5%.But the wave is more or less different especially the part of the post-arc.

在电磁暂态计算程序——EMTP/ATP中，根据实际情况建立了熔断器开断试验电路的仿真模型，其中熔断器模型采用一个时间变量非线性电阻和开关的组合来代替，前者代表熔断器熔断过程的弧前电阻，后者控制开断时间，两者均由ANSYS计算得到。

In order to make clear the phenomenon of current zero in the arc-quenching chamber of deion plates, the process of dielectric recovery and reignition of short arc between iron plates is investigated, and then the dielectric recovery strengths of various chambers are measured and compared. The different characteristics near current zero in the deion plate chambers are also analyzed based on experiments in the paper.

为弄清栅片灭弧室内电弧电流的过零过程，专门研究了不同条件下栅片间低压短弧的介质强度恢复过程和电弧重燃过程，然后测量了多纵缝和栅片灭弧室的介质恢复强度，对比了它们的熄弧性能，在试验的基础上，分析了栅片灭弧室中电弧电流的过零特征。

Steel billets are adopted edition of tran scription or strip steel, steel because of its riveting process does not fall into the stove with the pipe, electric arc welding arc-welded pipe and take the initiative; pipe material and its usefulness is not the same but is divided into: galvanized steel riveting , there is no rust steel riveted steel pipe.

钢管采纳的坯料是誊写钢版或者带钢，钢管因其铆接工艺没有同而分成炉焊管，电弧焊接管和主动电弧焊管；焊管因其材料和用处没有同而分成：镀锌铆接钢管，没有锈钢铆接钢管。

It was found recently that magnetic arc blow, inherently happens with such kind of welding process, particularly in deep groove welding of the first layer, can produce various kinds of weld defects, interfere the welding operation and make the arc length control system to work unproperly.

近年来在MIG焊研究中发现电弧磁偏吹现象严重，特别是坡口对接封底焊，会造成多种焊缝缺陷，甚至无法进行焊接，还会造成弧长闭环控制系统混乱。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。