查询词典 anti-friction

The action point of limiting force on retaining structure is not always at 1/3 of the height of retaining structures, but varies with the friction angle δ between soil and retaining structures, the type of limiting state, the failure mode, the internal friction angle φ, and cohesion c of the soil, ranging from 1/5 to 2/3 of the height of retaining structures.

3土体极限荷载P〓的作用点位置不象Coulomb理论中假定的那样，总是作用在墙高的1／3处，而是与土体极限状态的类型、土体的破坏形式、墙土之间的摩擦角δ、土体的内摩擦角φ和粘聚力c有关系，在挡土结构物高度的1／5到2／3的范围内取值。

The maxima of low-temperature internal friction peaks plot a symmetrical peak-like curve at logarithmic frequency spectrum and the peak-like curve shifts toward high frequencies with the increase of heating rate, indicating that phase transition relaxation time decreases; the maxima of high-temperature internal friction peaks exhibit a linear relation to the reciprocal frequencies, and as the heating rate increases its slope rises, which implies that the heating rate drives the normal movement of phase interface further in low-frequency measurements.

低温内耗峰峰值与对数频率呈现峰形函数关系，随升温速率的增加，频率峰向高频方向移动，相变弛豫时间减小；高温内耗峰峰值与倒数频率成直线关系，随升温速率的增加，直线斜率变大，表明低频测量时升温速率对相界面法向运动的驱动作用更强。

Even Monadnock didn';t ignore the reality and produced its friction lock batons – Classical Friction Lock.

即便是Monadnock也没有忽视现实，它生产了阻力锁定甩棍-- Classical Friction Lock。

A new nonreversible friction model is presented for sliding regime to describe friction memory effect.

同时还提出了一个新的不可逆宏观滑动摩擦模型。

The Paper analyses slipping master sheets of friction hoists, Nonskid calcution on lectotypeing design and regulating the relate to factors for friction hoistis is disussed.

本文分析了摩擦式提升机滑动的原因，讨论了选型设计防滑计算及对有关参数的调整。

The strength and toughness of the nanocomposites are improved because of the addition of anao-Zno. The volume resistance strength and toughness of the nanocomposites are improved because of the addition of nano-ZnO. The volume resistance coefficient is decreased 8×10 times, surface resistance coefficient is decreased 5.7×10^4 times, and the friction coefficient is decreased 29% by adding nano-ZnO. The friction, wear properties, and the antistatic property of MC Nylon 6/ZnO nanocomposite are better obviously than MC Nylon 6. The macro stress of MC Nylon 6 structure is changed by the tensile test so that the preferred orientation of crystal surface (002+202) is more obvious.

纳米ZnO的加入起到同时增强增韧的作用；使体积电阻系数降了8×10^4倍、表面电阻系数降了5.7×10^4倍、摩擦系数降低了29%，MC尼龙6/纳米ZnO复合材料摩擦磨损性能和抗静电性能明显优于MC尼龙6；经过力学拉伸试验的破坏，引起MC尼龙6结构发生宏观应力变化，造成（002+202晶面）产生明显的择优取向。

Starting from a barotropic model equations including large-scale orography,friction and heat factor,by means of scale analysis and small parameter method,then a barotropic quasi-geostrophic model with large-scale orography,friction and heating is obtained.

从包含大地形、摩擦及加热作用的正压模式方程组出发，通过尺度分析、小参数展开和线性化等方法，导出一个含大地形、摩擦及加热作用的准地转正压模式。

The formula was established about calculating design parameters and technological parameters of ideal strip and bent strip in the period of forming. The thesis presented how to calculate the deformed area length and contact are radius of contact deforming between two elastic bodies on condition of the friction. The calculating formula of pinch force about plate-strip pinch mill was given and the results were analyzed that friction coefficient and radius of pinch rolls are very important for determining pinch force. Moreover, the rule of deforming and stress distribution of different 〓 ratio were gained on condition that the deforming was considered to be non-uniform distribution in the gap. The differential equations were got that calculate the displacements of large deflection of elastic cantilever rectangle plate with fixed end and the formula of the Finite Strip Method was conducted to study the regularity of mid-plane displacements, deformation and stresses for elastic-plastic large deflection bend of cantilever parallelogram plate with fixed or slidable end by integrating Prandtl-Reuss equation.

建立了一套完整的设计参数计算公式和在成型过程中理想带钢或具有月牙弯带钢的工艺参数的调整公式；在考虑摩擦力的条件下，对两弹性体接触变形过程中的接触变形区长度和接触弧半径用位移解法进行了研究，推导了板带递送机的递送力计算公式，从而得知在递送机设计过程中，应选择适当摩擦系数和辊身直径；另外，还从辊缝内带钢实际变形出发，分析了对于不同的〓值，带钢的变形规律及应力分布状况；建立了固定端悬臂矩形板弹性大挠度弯曲变形的控制方程，并且在对Prandtl-Reuss方程的积分处理的基础上，导出了固定端和滑动端悬臂平行四边形薄板的弹塑性大挠度的中面伸展位移、变形和应力的有限条元法公式，编写了Fortran语言计算程序，在各种参数条件下，对螺旋焊管成型过程变形规律进行了全面的分析研究，从而为螺旋焊管的生产和进一步的改进提供了理论依据。

In this paper, the friction mechanism of engine piston ring / cylinder friction system was reserched.

本论文对发动机的活塞环／汽缸套这对摩擦副进行摩擦机理研究。

It is shown by the friction material behavior tests that the friction material behavior is influenced not only by its mechanical properties, such as hardness, modulus of elasticity, yielding stress and Poisson's ratio etc., but also by its chemical constitutions.

通过对摩擦材料的研究说明：摩擦材料的性能不仅受材料的力学特性，如硬度、弹性模量、屈服应力、泊松比等因素的影响，而且还受其化学组成的影响。

Hanna: That's over now, isn't it?

都结束了，对吗

You must be ill. You look so pale.

你一定是病了，你的脸色苍白。