查询词典 anti-friction

Figure 2 printing plate gaskets is higher than the 0.2 ~ 0.3mm hobber pillow, blanket below the occipital hobber 0.05mm, a2, B2 Department produces a smaller convex hull, of course, less friction and sliding, wear plates, no szlama and "" taping, fault-printing plates and high, less hierarchical dot gain, clearly, the life expectancy of the machine, the electrical power consumed less.

图2印版的衬垫矮于滚枕0.2～0.3mm，橡皮布矮于滚枕0.05mm，在A2、B2处爆发的凹包较小，当然摩擦和滑动也多，印版磨损较多，无不推不净和"杠子"障碍爆发，印版的耐印率矮、网不面放大多，条理纯楚，机械的寿命放大，电机耗电也多。

The result shows that the F-DLC films were distributed compactly and homogeneously and exhibit good friction-reducing behaviors.

测试结果表明，制备的薄膜整体均匀致密，表现出了良好的减摩性能。

The results show that the synthetic properties of geological drill rod by friction welding are better than that of the hot upset forged drill rod.

结果表明，与热镦粗的钻杆相比，摩擦焊接的地质钻杆具有良好的综合性能。

The main results of the investigation are as following:(1) Some important criteria for the design of multi-layer structure are acquired: the ratio of the layer thickness to the contact diameter should be controlled to a value about 0.8; increasing the number of the gradient layers and elasticity modulus of the top layer would benefit to the yield strength and the stress status at the interface.（2）By means of molecular dynamics simulations for a indentation and sliding process, it is discovered that dislocations of 45 direction to the surface occur in the surfaces layer, which is correspond to the direction of the plastic flows observed in the macroscopic continuous medium. The irreversible deformation caused by the dislocation and the atom piles at the surface are responsible for the irreversibility of the force response. They are also the main factors for the friction generation. The temperature and the indentation velocity have significant effects on the deformation behaviors of the material of the surface layer. The yield strength would increase obviously if the indentation velocity is greater than 10 m/s.（3）A method to evaluate the fracture toughness of coating by estimating the crack-density functionβof a Wicker''s indentation was proposed. Meanwhile a new surface treatment technology was developed using non-equilibrium plasma.（4）A MD-FE hybrid method and corresponding software was developed to analysis the tribological behaviors for multiplayer system.

研究主要内容和结果有：（1）得到指导梯度膜设计的几个准则：控制膜层厚度与接触半径比在0.8左右为宜；适当增加梯度层层数和顶层弹性模量，有利于提高抗屈服能力和改善界面处的应力状态；（2）通过对嵌入和滑动摩擦过程的分子动力学模拟，发现表层产生一个与宏观连续介质的塑性流动方向观测一致的45 方向位错；位错造成的不可逆变形和表面的原子堆积，是力的响应不可逆性的原因，也是构成摩擦力的主要因素；温度和嵌入速度对材料变形特性有显著的影响，当嵌入速度大于10 m/s时，屈服强度明显增加；（3）提出压痕裂纹密度系数β半定量判定膜层断裂韧性的方法；并开发出表面强化新工艺；（4）开发出分析表面摩擦学特性的MD-FE复合模拟方法和相应模拟软件。

Friction loss factors of hydraulically smooth pipes have been calculated by using several different turbulent models.

应用几种不同的湍流模型，模拟计算水力光滑管的沿程阻力系数。

It is seldom reseached the mechanism of highspeed and long-range. On the basis of detailed investigation on the Touzhai landslide, the author have expatiated on the environment condition, studied the moving characteristics of each stage, the laws of friction coefficient of the sliding surface in the set-out stage and the erodynamic effect in the short-range, analyzed the hydrokinetics mechanism of highspeed and long-range.

本文在去现场详细调查的基础上，阐述了头寨滑坡的环境条件，研究了头寨滑坡全程各个活动阶段的运动特征，通过试验研究了头寨滑坡启程活动阶段滑面高速摩擦的规律和近程活动阶段滑坡凌空飞行的空气动力学效应，从流体动力学的观点分析了头寨滑坡高速远程的流体动力学机理。

The sensor unit of YZ-CCD type automatic hypsometer, in which the CCD is used, has no excursion and friction in the work. Because the altitude measurement of different levels is settled, this kind of hypsometer has the very good prospects in economy and application.

YZ-CCD型传高仪中的传感单元采用新型CCD光电器件，传感器的特点是无漂移、无摩擦，仪器较容易地解决了不同层面的高程传递问题，具有推广和应用价值。

When the temperature is fixed, the internalfriction increases with the increasing magnetic field, and anobvious hysteric behavior of the internal friction is observedwhen the magnetic field is looped.

面当温度固定不变时，内耗随着磁场的增大而增大并且在循环磁场中表现出明显的滞后行为。

In a theoretically friction less, or ideal, machine, the work input and work output are equal, and the efficiency would be 1, or 100%.

理论上，一个无摩擦力的，或者说是理想的机器，输入和输出的功相等，因此效率是1，或者说是100%。

Combined with the investigation of SEM and other methods of interface analysis, we found that in the impact fracture process, matrix deformation, fiber pull out, interface debonding between matrix and fiber, interface friction induced by debonding, new surface appearance and so on all can absorb impact energy.

此外，研究还发现G系列坯料即使烧结至1500℃，在熔剂的配入量达不到50%情况下无法烧结，这一试验结果能用颗粒体随机堆积气孔率和本文提出的聚合体颗粒堆积的分数维结构模型得到解释。

He paid $5,000 for this cupcake.

他我这个纸杯蛋糕花了5000美元。

I mean, if you want to, that is

我的意思是，如果你们想吃的话。