查询词典 anti-friction

That the curves of the normal force and friction force between two corresponding gear teeth in a given condition can supervise the design and optimization of gear system.

得到了某一特定传动条件下单对齿轮轮齿法向力及齿间摩擦力的变化规律曲线，从而可以指导齿轮系统的设计和优化。

At the same time, in the transmission system of construction machinery up-to-date, the power transferred by the transmission is improved greatly, while the gear friction is adopted in the transfer structure, so the heat loss will influence both the lubrication and cooling of the system, and the working intensity of the structure components. Therefore, the correction of the heat balance is necessary to the system.

同时，在现代工程机械的变速传动系统中，由于行星变速箱所传递的功率有了大幅的提高，但传递结构依然大量采用齿轮摩擦传动，其热损失不仅对系统的润滑和冷却有影响，而且对结构元件的工作强度也具有很大的影响，因此，也需要对该系统进行热平衡校核。

This is because the angle on the worm is so shallow that when the gear tries to spin it, the friction between the gear and the worm holds the worm in place.

这是因为，蜗轮蜗杆的升程角很小，当涡轮要带动蜗杆时，蜗轮蜗杆间的摩擦力把蜗杆锁住了。

However, the influence both ship hull deformation and friction between gear teeth are omitted in strength calculation of gear driving fixed in boat in traditional design.

算例表明，船体变形及齿间摩擦时齿轮强度的影响的确不可忽视。

The linear regression of the three factors—seed diameter, length of friction and gear gap to the hulling efficiency was determined and the significance of the regression equation was tested.

通过以籽粒粒径、碾搓行程和破壳装置动、定齿盘间隙为研究对象的三因素三水平重复试验，得出了此三者与破壳效果间的线性回归方程，并做了回归方程的显著性检

Heavy haul freight car; spring friction draft gear; impacting test; numerical simulation

重载货车；弹簧摩擦式缓冲器；冲击试验；数值仿真

With Simulink, you can move beyond idealized linear models to explore more realistic nonlinear models, factoring in friction, air resistance, gear slippage, hard stops, and the other things that describe real-world phenomena.

藉由 Simulink ，你能超过理想化线性的模型移动探究比较现实的非线性模型，磨擦，空气阻力，齿轮滑动量，硬式障碍物的贷款保收，和描述真实的现象其他的物。

Involute gear ; friction coefficient between teeth ; tooth number ; driven gear ; output torque ; fluctuation ratio

渐开线齿轮；齿间摩擦系数；齿数；从动轮；输出扭矩；波动率

Some groups of numerical models were built with different design param- eters of die,geometric parameters of gear,friction conditions or processing conditions,and the service loads were in- vestigated.

以成形时所需载荷为评价指标，就影响成形工艺的模具设计参数、齿轮特征参数，摩擦条件和工艺条件进行分组建模分析。

The gearbox has three wet multi-disc friction clutches, and during gear shifting, the clutch discs are pressed by the oil pressure-driven piston acting along the shaft.

变速箱有三个多片湿式摩擦离合器，换档时相应的离合器摩擦片被轴向作用的油压所推动的活塞压紧。

He paid $5,000 for this cupcake.

他我这个纸杯蛋糕花了5000美元。

I mean, if you want to, that is

我的意思是，如果你们想吃的话。