查询词典 antenna circuit

There are three parts in our design: first, the dual-band branch line coupler provides two equal-power signals with 90° or -90° phase difference in each operating band. Second, the wideband switching circuit controls the two output powers of branch line coupler to excite the antenna structure for producing linear polarization wave or circular polarization wave. Third, the L-shaped fed conventional planar patch antenna is provided to overcome the coupling effect.

整体架构包含三个部分：L形电容耦合馈入式平面天线是为了克服平面式微带天线窄频的缺点；双频枝干耦合器提供天线在操作的两个频率点上各输出两组相差正九十度与负九十度的讯号，最后宽频的切换电路是将枝干耦合器的两组讯号作分配用以激发不同方向的天线以产生线性极化模态或同时激发两个垂直的天线以产生圆形极化模态。

Based on the project of Cruise Antenna for Receiving DBS Video Signal, we analyze and design the foreside antenna and the circuit of comparing intensity of signal received f...

本文结合"DBS数字卫星广播移动接收天线"项目，对其前端天线进行了研究与实现，并对天线在载体移动过程中寻星和锁定卫星的关键电路—接收信号幅度比较器进行了研制。

Based on the project of Cruise Antenna for Receiving DBS Video Signal, we analyze and design the foreside antenna and the circuit of comparing intensity of signal received from DBS satellite in this paper.The project has the great achievements as below.?

本文结合"DBS数字卫星广播移动接收天线"项目，对其前端天线进行了研究与实现，并对天线在载体移动过程中寻星和锁定卫星的关键电路—接收信号幅度比较器进行了研制。

A small planar antenna combined with a printed circuit board. First and second ground layers formed on top and bottom surfaces of the dielectric layer, respectively, corresponding to each other; and a first antenna unit which extends from a side of each of the respective first and the second ground layers, for radiating a first polarized wave with the application of current.

一种与印刷电路板组合的小型平面天线，在具有预定厚度的介电层的顶表面和底表面上形成相对应的第一和第二接地层，第一天线单元和第二天线单元分别以预定图形从第一和第二接地层的一侧伸出，分别通过施加电流来辐射正交的第一极化波和第二极化波。

In chapter one, the function and components of RF block in smart antenna are discussed, and the block schematic of RF circuit in smart antenna system at 3.95GHz and 1.9GHz is analyzed.

首先介绍了智能天线研究背景、发展历史，以及射频前端在智能天线中的作用和组成。

Based on the project of Cruise Antenna for Receiving DBS Video Signal, we analyze and design the foreside antenna and the circuit of comparing intensity of signal received f...

本文结合&DBS数字卫星广播移动接收天线&项目，对其前端天线进行了研究与实现，并对天线在载体移动过程中寻星和锁定卫星的关键电路—接收信号幅度比较器进行了研制。

The design of hardware include design of RF ReadAVrite module, design of MCU circuit, design of serial communication circuit, design of RF power amplifier, design of RF signal processing circuit and antenna design.

根据项目参数要求，在硬件方面，进行了射频读写模块电路设计、微控制单元电路设计(微控制器选用W78E58B)、串行通信电路设计、射频输出功放电路设计、射频输入信号处理电路设计和天线设计。

P.41: The physical dimension of the antenna determines the amount of inductance of capacity existing in the circuit and consequently the resonant frequency of the antenna system.

天线尺寸决定回路中的电感量和电容量，从而也决定天线系统的谐振频率。

The system comprises first and second antennas for receiving first and second RF signals of first and second frequencies, respectively; a mobile switch for measuring performance characteristics of the second antenna; and a switch circuit connected between the second antenna and the mobile switch for controlling flow of the first RF signal to the second antenna.

在移动通信终端内，一开关电路，用于根据工作模式控制CDMA天线的输入阻抗，该开关电路被连接在CDMA天线和移动开关之间，以便在GPS工作模式下维持CDMA天线的输入阻抗为高阻抗，来切断GPS信号的流入，以及在CDMA工作模式下维持CDMA天线的输入阻抗为低阻抗以接收CDMA信号。

The proposed antenna consists of a rectangular metal patch on a printed circuit board fed by a 50- coplanar waveguide. By cutting a C-shaped slot in the rectangular radiating patch,a frequency band notch will be created. The proposed antenna yields an impedance bandwidth of 3.1-10.6GHz with VSWR,except the bandwidth of 5-6GHz for WLAN.

天线采用印刷电路板上的矩形贴片作为辐射单元，并由同一面上的共面波导馈电，通过在矩形贴片上开一个C形槽来实现陷波功能，电磁仿真软件Ansoft HFSS10的仿真结果显示，合适地选择C形槽的尺寸可以调整陷波的中心频率和带宽。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐