查询词典 angle

This is a right angle ; that is a sharp angle.

这是一个直角，那是一个锐角。

An angle of 90°is called a right angle.

90°的角叫直角。

An angle of 90 degrees is called a right angle.

90度的角叫做直角。

Long gradually expands the tube regarding the conventional structure right circular cone, looked from the mobile angle, when design catalytic converter, in principle should use the small cone angle divergent tube.

2对于常规结构的直圆锥长渐扩管，从流动的角度来看，设计催化转化器时，原则上应采用小锥角扩张管。

Right-angle fold: Refer to folds that are at right-angle s to each other.

直角摺：纸张的一摺和前一摺成直角的摺法。

To obtain the relationship between rotary dynamic target axis shake and its precision,rotating vector and coordinate transfer are used to analyze axis shake′s influence to target′s high and low angle and azimuth angle,and then to analyze its error.

旋转动态靶标是用来检测大型光电经纬仪跟踪精度和动态精度的设备。

The reflection of the LO mode, RLO, and its ratio, RLO/RTO, with the reflection RTO of the LO mode increase with increasing angle of incidence. In the case of the polarized incident light,ωLO is a function of angle of incidence and polarization state of the incident.

在45°入射角附近，ωLO几乎与入射光的偏振方向无关；在这个临近角45°两侧，ωLO和入射光的偏振方向的关系呈现相反趋势：当入射角小于45°，ωLO随着入射光极化仰角θ的增大而减小，当入射角大于45°，ωLO随着极化仰角θ的增大而增大。

There are several variables that determine these positions; crank length, distance from crank center or bottom bracket to saddle, saddle angle, seat tube angle and saddle offset, distance from saddle to handlebar, relative height of saddle and handlebar, handlebar width, and handlebar drop on road style handlebars.

有几个数值决定了这些位置的所在：曲柄的长度、五通中心到坐垫的距离、坐垫的角度、坐垫表面的材料、坐垫和车把之间的距离、坐垫和车把到地面的高度。车把的宽度、以及公路车把的下垂的角度。

The first one is to generate the circle for each borderline segment of the component by considering the segment length and the prescribed tolerance value. If this is not the case, the borderline segment will be equally divided into halves until the obtained circle satisfies the tolerance value over the whole borderlines of the component. The basic idea of the last two algorithms aims at covering the domain occupied by the component as much as possible. The circle generation is carried out sequentially from salient angle to the sector formed by the salient angle till the uncovered borderline segments of the component. Particularly, the three-step algorithm with gap allows that the generated circles are distributed with gap along the component contour.

二分法利用组件各边长度和设置的容差大小得到该边的候选包络圆，若该圆不满足组件所有边的容差要求，则将该边不断地对分，直至所得到的包络圆满足各边的容差要求；三步划分法和带间隙的改进三步划分法则以组件区域为划分对象，依次对组件多边形凸顶角、凸扇形区和多边形各边剩余线段划分包络圆，且带间隙的改进三步划分法则允许包络圆在组件边界上以适当的间隙分布。

The cohesion and the internal friction angle are functions of water content index; cohesion-degree of saturation curve and internal friction angle-degree of saturation curve are gotten by simulating shear experiment through different paths, through which shear strength parameters can be obtained; CDSC and IFADSC are approximating straight lines in the same path when the change of saturation degree is small.

非饱和土抗剪强度的黏聚力和内摩擦角是含水指标的函数；通过模拟不同路径下非饱和土抗剪试验，得到黏聚力-饱和度曲线和内摩擦角-饱和度曲线，进而得到非饱和土抗剪强度指标；在同一路径小区间范围内CDSC和IFADSC曲线近似为直线。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。