查询词典 angle

X-ray diffraction is one of the most common and efficient ways to measure a superlattice structure. This dissertation displays the detail results for characterization of Ge〓Si〓/Si superlattices by x-ray diffraction (including x-ray small angle diffraction and double crystal diffraction). It was found, when the growth temperature is lower, the intensities of xray small angle diffraction peaks are modulated by a periodical function, which indicates that both sets of interfaces of the superlattice is highly flat; when the growth temperature is higher, the diffraction peak intensities are simply decay with the increase of diffraction vector, which indicates that one set of interfaces is highly flat but another is not; when the growth temperature is very high, the diffraction peaks are reduced more rapidly, which indicates that both sets of interfaces are not ideal.

本文详细介绍了用X-射线衍射（包括X-射线小角衍射和双晶衍射）方法对Ge〓Si〓/Si超晶格结构特性测试的结果，尤其是发现，当Ge〓Si〓/Si超晶格的生长温度较低时，X-射线小角衍射谱峰的强度随着衍射波矢的增加而周期性调制，表明超晶格的两套界面都十分平整；当生长温度较高时，Ge〓Si〓Si超晶格的X-射线小角衍射谱峰的强度随着衍射波矢呈简单的衰减变化，对应于超晶格内有一套界面不平整的情况；当生长温度进一步提高时，X-射线小角衍射峰明显减少，表明超晶格内两套界面都不理想。

One limb dips to the north with a dip angle of 46 degrees and the other limb dips to the south with a dip angle of 48 degrees.

其中一个翼倾向北，倾角46度，另一个翼倾向南，倾角48度。

One limb dip s to the north with a dip angle of 46 degrees and the other limb dip s to the south with a dip angle of 48 degrees.

其中一个翼倾向北，倾角46度，另一个翼倾向南，倾角48度。

This paper introduces the developing conditions of big dip angle belt conveyor in our country,generalizing the five kinds of main type and their principal uses of big dip angle belt conveyor.

介绍国内外大倾角带式输送机的研制状况，概述大倾角输送机的5种主要类型及其用途。

Under the influence of angle of joint and load, the distributing of displace field exits non-uniformity, and with the increase of joint dip angle the non-uniformity become stronger.

6受节理和加荷方向的影响，位移场分布存在一定的不均匀性，随着节理倾角变大，不均匀性增强。

The design method is described, and the calculation results are presented under the standard air conditioning condition. The working process of the two-stage expander is discussed, and the difference between the two-stage expander and the conventional one is stated. In addition, the influence of the dip angle on the expansion chamber volume is analyzed. The results show that the dip angle has little effect on the expansion chamber volume and it is suggested that the effect may be neglected in the expander design.

介绍了该膨胀机的设计方法，给出了标准空调工况下的计算结果，详细讨论了两级旋叶式膨胀机的工作过程，并对两级膨胀机与传统旋叶式膨胀机的区别进行了论述，最后分析了滑片倾角对工作腔基元容积的影响，结果显示，滑片倾角对工作腔基元容积的影响很小，在膨胀机的设计过程中忽略滑片倾角的影响是合理可行的。

Research shows that the main factors influencing forging penetration efficiency are reduction in pass and the dip angle of the hammer, and the main factors influencing forged piece surface quality are axle feeding speed and rotation angle.

研究表明：影响锻透性的主要因素为道次压入量和锤头倾角；影响锻件表面质量的主要因素为轴向送进速度和旋转角度。

It can meet the requirements for many types of typical layout, such as 500-1400mm belt w idth, dip angle of 0°-18°, and surrounding angle of 190°-210°.

可满足带宽500～1400mm 、倾角0°～18°、围包角190°～210°多种型式的典型布置。

Many phenomenon due to deep dip angle coal seam mining are still explained very well. There are a lot of deep dip angle coal seam mining district in China, the problem of miming subsidence is very general, so the research is of theory mining and practical value.

实践中，我国很多矿区有大量的倾斜煤层存在，倾斜煤层开采沉陷与变形预计问题普遍存在，需要我们对这类矿山的地表移动规律问题进行全面研究，因而该项研究具有重要的理论意义和生产实用价值。

The stress distribution on the wall of directional well is analysed, and a borehole stability model for the formation with dip angle in directional well is established. The influences of dip angle and trend on borehole stability are discussed.

建立了弱面地层数学模型，分析了斜井井壁岩石应力状态，推导出了井壁岩石最大主应力与低强度地层法向夹角的计算公式，建立了用于大倾角地层钻井液密度安全下限的力学模型，详细分析了倾斜地层的倾角和走向对井壁稳定性的影响。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐