查询词典 angle

Simulation result shows that the alignment accuracy was 5' for east direction maladjustment angle error, 2' north direction maladjustment angle error, and 6' for azimuth maladjustment angle Error.

仿真结果表明该方案的对准精度(1σ)可以达到东向失准角误差为5角分，北向失准角误差为2角分，方位失准角误差为6角分。

The result indicates, under the condition of big initial error and shell"s high speed rolling, after 60 seconds" flight alignment, the error of azimuth angle and attitude angle can be decreased to no more than 10 angle second, and the position and velocity error has been corrected. This shows the effective of our designed arithmetic.

研究结果表明：在初始误差较大、弹体高速旋转的条件下，经过60秒的空中对准，三个姿态角误差可降至10个角秒以下，同时位置和速度误差得到了修正，从而验证了算法的有效性。

Results show that the milling tool with rake angle 5°, clearance angle: 10°, helix angle: 45° and corner radius: 1 mm is tested on the surface integrity experiment.

实验结果表明，前角5°，后角10°，刀尖圆弧半径为1mm，铣刀螺旋角为45°的几何结构铣刀完成了表面完整性试验中。

The distribution of branch angle was corelated to DINC of branch,the branch angle distributed in upper layer of canopy were generally small and with DINC increase the branch length of middle layer of canopy began to proglong,simultaneously,the weight of branch increased with branch diameter and length,hence,the branch angle of origin increased obviously and took the majority proportion.

着枝角的分布与着枝深度有密切的关系，着枝角度在树冠的上层时一般都较小，而随着树冠深度的增加，中层的枝条的枝长开始增大，枝条的重量随着基径和枝长在增大，着枝角度会明显增大，因此在这个范围内的分布最广，占了大多数。

Figure 9-45 indicates a universal dividing head, which consisits of the body, the swivel block, the woekpiece (with one of its ends supported by the center of the work spindle) is rotated through the desired angle by rotating the index crank through an angle that is dependant upon the desired angle.

图9-45显示一个普遍的分度头，其中consisits的机构，旋转座的woekpiece （同一个目的支持中心的工作主轴）是理想的旋转角度，通过旋转该指数通过一个曲柄角度取决于所希望的角度。

The discussion on the evaluation method of the current code on the resistant capacity, the evaluation on the yield drift angle, the peak point drift angle and the ultimate drift angle of different section are studied.

本文在试验的基础上对现行规范剪力墙承载能力估计方法、不同截面特征的剪力墙屈服位移角、峰值位移角和极限位移角的估计方法进行了探讨。

Employing the method of complex helical drill point design,the formula of the clearance angle of inner cut edge for the socket drill is derived and the relationship between the clearance angle and the slantwise angle of the inner cut edge is deduced to innovate the design and manufacture of the socket drill.

通过复杂螺旋面钻尖设计方法导出锪窝钻钻尖内刃后角公式及内刃后角与内刃偏角的关系表达式，改进了锪窝钻的设计与制造。

Leaf angle above ear of super high yield maize was less than 20°, leaf angle of ear was between 25°and 35°, and leaf angle below ear was about 35°.

根冠关系分析表明，根系分布越集中，在深层土壤中分布比例越大，株型越紧凑。

The effects of swirling airflow and divergence angle, in the airblast atomizer on the atomizing performance were studied.Six different atomizers having three kinds of blade angle -swirlors and three .kinds of exit divergence angle have been, tested, and the results have been analyzed.

本文研究了空气雾化喷嘴内气流旋转及出口扩张角对雾化性能的影响关系，对装有三种不同叶片转角的旋流器及三种出口扩张角的喷嘴试件进行了试验和分析。

For five-coordinate NC end milling, the author gives the equation of tilt angle, the optimum algorithm of tilt angle, the analysis of machined errors, the compensative algorithm for cutter axis tilt error, and the formulae of feed length, feed width and cutter axis swing angle.

推导了五坐标端铣数控加工中的后跟角计算公式，提出了后跟角的优化计算方法——刀盘周边7点干涉检验法，分析了各种加工误差，提出了刀轴摆动误差补偿方法——刀具切触点偏置法，给出了走刀步长、切削宽度以及刀轴摆角的计算公式。

Shop assistant: Please check at the door.

店员：请您到门口柜台交费。

In the end, transportation of PAHs in the environmental matrix was preliminarily investigated and discussed according to PAHs data of soils and sediments from a certain region in Shanghai. The result indicated that there are two or more pathways on PAHs transportation in the environmental matrix.

最后，对上海特定地区内PAHs在环境介质中的迁移径途进行了分析讨论，结果表明上海市土壤和沉积物等环境介质中PAHs的迁移存在多种途径。