查询词典 angle shear

Furthermore, finite element program ABAQUS6.5 was also used to simulate experimental course. Results show that the change of ply splice angle will lead to shear stress concentration on 0 ply in splice region. But the average of shear stress along notch root of specimens almost does not change.

采用有限元软件ABAQUS6.5对实验过程进行模拟，得到拼接层角度改变将引起拼接层中0层出现切应力集中，但沿缺口切应力的平均值几乎不变。

A theoretical model for calculating the cutting angle with different crystal planes, orientations and tool orthogonal rakes are described in this paper. It is built with the ultra-precision cutting model by the principle of the maximum specific energy of shear deformation and the mechanism of change of the shear modulus with...

本文利用剪切变形比能最大及单晶材料不同晶面晶向剪切弹性模量不同的原理，结合超精密切削模型，从理论上计算出不同晶面、不同晶向及不同刀具前角超精密切削条件下的剪切角，得到其在不同切削条件下的变化规律，并由此解释了切削加工中由KDP晶体各向异性所导致的工件表面粗糙度的各向异性。

The concept of negative shear zone and negative shear angle are proposed in study.

提出了负剪切角及负变形区的概念。

And the distribution of the magnetic shear angles exhibits the hemisphere sign rule as the asymmetry of helicity. In our dataset, 53% of the active regions in the south hemisphere have positive shear angle and 62

磁场剪切角具有南北半球符号的反对称手征性，在南半球有53％的活动区的磁场剪切角是正的，而在北半球有62％是负的。

The shear angle in the shear plane will crease with the cutting velocity.

切屑剪切平面之剪切角会随著切削速度的增加而增加。

Fractography analysis shows that the global tension failures trimly,because of matrix cracks and tension fracture of fiber and the compression specimens failure in a shear plane about a little angle to the compression loading direction because of delamination and longitudinal fiber shear fracture.

其拉伸断口较为平齐，基体开裂以及纤维拉伸断裂是主要破坏形式；压缩破坏呈现剪切断面，压缩断面和压缩加载方向形成一个较小夹角，层间分层和纵向纤维剪切断裂是其主要破坏形式。

Under the condition of small strain, the initial value of shear modulus increased along with the increment of angle θ between trail stress paths and recent stress history. If the two directions were entirely reverse, the effect of stress path circumgyration on shear modulus was the largest; if they coincided completely, the effect was very feeble.

研究表明，在小应变范围内，剪切模量的初始值随试验应力路径与近期应力历史间的夹角θ的增大而增大，当两者完全相反时，应力路径旋转对土体在小应变条件下的剪切模量影响最大；完全一致时，其影响最弱。

According to the distribution rule of interbedded drift angle in buildings and variational rule accompanying change of stiffness characteristic value, the paper puts forward the advice about how to differentiate normal structure story in structure design drawings and the influence factor which should be considered. The author also advances his opinion and suggestion about how to judge the rationality of stiffness arrangement of frame-column and shear wall in frame-shear structure.

就层间位移角在楼层中的分布情况和分布规律以及随刚度特征值变化的规律，提出了在结构施工图设计中如何划分结构标准层的建议和应考虑的影响因素：并就判断框—剪结构中框架柱与剪力墙刚度分配是否合理的具体方法提出了自己看法和建议。

The results clearly prove an evolution mechanism of type B PLC shear bands, that is, a PLC shear band first nucleates at one side of specimen, then transversely runs through the entire specimen section with a certain angle, finally forms an inhomogeneous deformation bands.

实验结果清楚地证实了B型PLC剪切带的一种演化机制，即先在试样一侧成核，然后与拉伸轴成一定角度横向贯穿整个试样，最终形成非均匀塑性变形带。

The mechanism of MSW's shear strength is stated in this thesis. The underlying cause for the phenomenon that the cohesion of MSW increases with depth while angle of shear resistance doesn't is detailed explained in this paper.

本文阐述了填埋体的抗剪强度机理，解释了填埋材料凝聚力随深度增加而内摩擦角基本不变这一现象的物理根源。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。