查询词典 angle of vision

Blade twist angle may be automatically established by a balance of dynamic forces on the blade which cause twist angle to increase as root mounting angle is increased.

叶片扭角可自动建立一个平衡的动态部队对叶片造成扭角增加，以root的身份安装的角度来看是有所增加。

The definition of generator angle is proposed in this paper. A new method to deduce generator angle by using rotor rotation signal is illustrated, which compares the phase difference between GPS timing pulse and RRS. Using only mechanical signal, the technique unfreezes limitation of zero-cross of generator terminal voltage during transient process. Automatic correction of initial generator angle is also proposed .

本文介绍了同步发电机绝对转子角的定义，提出了一种测量绝对转子角，进而获得高精度的相对转子角的方法；此方法不使用机端电压过零整形脉冲，而是将机组键相脉冲与GPS 定时脉冲比相，并能够自动整定初始位置角，因此，测量结果不受发电机运行状态的影响，能够在各种运行方式和扰动情况下获取高精度的绝对转子角。

The Kuriles subuction zone subducts with an angle of 45°; while the subducting angle of the Japan Sea subduction zone may by smaller 30°; the Ryukyu and Izu-Bonin subduction zones subducts with an angle of over 70° or nearly 90°, providing an evidence for activities in back-arc basins.

千岛群岛俯冲带大约以45°角度俯冲，日本海俯冲带则可能小于30°，琉球群岛俯冲带和伊豆-小笠原俯冲带则以大于70°的角度或近于直立的角度俯冲，从而为弧后盆地的活动性提供了证据。

The experimental velocities cover subsonic,transonic and supersonic flows,and the content includes:(1) flow over flat plate,revolution body and wing with riblets surface at zero angle of attack;(2) the effect of pressure gradient,angle of attack and slide angle;(3) the burst characteristics,characteristics of turbulence,the streak structure in the near wall region and the drag reduction mechanism.

内容涉及沟槽面平板、旋成体、机翼等在压、跨、超音速流动情况下的实验研究成果；压力梯度、攻角、侧滑角等的影响；湍流猝发特性、紊动特性、近壁区带条结构的特征及减阻机理等方面的工作。

The sheath inserted directly in the Department indicating the degree of bounce angle and a yellow dot that low bounce angle (the smaller the width at the bottom), two Yellow-spotted as a standard rebound angle, another perspective of the figures that rebound.

该公司直接在插鞘处标明反弹角的程度，一个黄点表示低反弹角，两个黄点为标准反弹角，另外数字则表示反弹角度。

At present, the location of the anti-lopsided wear centralizer used in fields is mainly based on the deviation angle. In fact, lopsided wear may be caused by the change of azimuth angle or by the vertical well section and hold angle section during the working of the bucket rod.

目前油田矿场主要根据井斜角来确定防偏磨扶正器下入位置，实际上方位角变化也能导致偏磨，抽油杆杆柱在运动过程中直井段和稳斜段也会产生偏磨。

According to the results of this study, the ultimate strength of pin-bone interface increased as the moment arm decreased and torque increased. When the pin-bone angle approached 90°, the ultimate strength was the largest and as the angle decreased, the ultimate strength decreased. There was no significant difference between rigidity and torque, but rigidity decreased as the skull-bone angle decreased.

结果发现钉骨界面的极限强度在头圈距离颅骨的力臂短时较高，且随著所用扭力的增加而增加，当头钉与头骨表面的夹角成垂直时最强，随著夹角越趋锐角而渐减，钉骨界面的刚性与扭力并无明显关系但与夹角有关，夹角垂直时刚性最高，而后随著夹角渐趋锐角而递减。

In order to real-timely and accurately measure thread parameters such as thread angle(tooth-type half-angle),screw-pitch,lead,thread height,major diameter,minor diameter,pitch diameter,helix angle etc,and enhance the measuring accuracy,a non-contact thread parameter measuring system based on an array CCD was designed and achieved.

为实时准确地对螺纹的牙型角、螺距、导程、螺纹高度、大径、小径、中径、螺纹升角等参数进行测量，并提高测量精度，设计并实现了基于面阵CCD的螺纹参数非接触测量系统。

To further study this problem, the optical axis is rotated by an arbitrary angle. A striking phenomenon is discovered that the Brewster angle is always equal to the rotation angle. This is because the waves in the direction perpendicular to the optical axis become evanescent since the permittivity is positive while the permeability is negative in this direction.

然后进一步的研究了主轴不垂直于界面的情况，发现主轴转动的角度恰好等于此时的Brewster角，这是因为此时垂直于主轴的方向上介电常数为正磁导率为负，只有倏逝波而没有可传播的波存在，因此反射系数为0。

For improving the maneuver stability,safety and decreasing the tire wear,the combination of the optimization software,modefrontier and msc.adams,is applied to design the steering mechanism,with bottom angle of steering trapezoid,arm length,kingpins distance and axles distance as design parameters,transmit angle as constraint,minimum error between theoretical and practical steering angle as objective function,and simulated annealing as the optimization algorithm.

为了提高汽车操纵稳定性、安全性及减少轮胎磨损，将数值优化软件modefrontier同机械动力学仿真分析软件m sc.adam s集成，以转向梯形底角、转向臂长度、主销中心距和轴距为设计参数，传动角为约束，以转向时内轮实际转角与理论转角的误差最小为目标函数，采用模拟退火算法对转向机构进行最优化设计。

Listen,point and check your answers.

听，指出并且检查你的答案。

Warming needle is one of effective treatment methods for knee arthralgia aggravated by cold,and it is simple,safety,so it should be developed in clinical acupuncture and moxibustion extensively.

但以本院科针灸门诊在2005年1月—2006年6月期间共收治膝痛患者100余例，经过临床的诊断后，其中施以温针治疗的48例，疗效显著，报道如下。1临床资料本组病例48