查询词典 angle of deviation

The relation between modified angle and structure angle was given at 303nm, and the relation of the deviation angle with wavelength was also investigated.

以303nm波长为例，给出了修正角与结构角的关系式；还研究了透射光束的偏离角与波长的关系，并通过数值计算软件进行了分析。

By 35. 18°. The standard deviation σ was representative of mean deviation angle 〓, which characterized commendably the degree of misalignment grains.

当取向磁场为1.5T，粉末的松装密度各为23％和32.3％时，平均取向度分别为0.945和0.892，与之对应的磁通分布标准均方差为3.654和6.688。

Based on the method of minimum deviation angle, man can obtain the accuracy of measuring refractive index of glass at 3×10-6 with fine apparatus for measuring angle, but the classical princip1e formula quoted by these literatures have principle formula error about 4 ×10 - 4 order which lead to an erroneous measure result.

在这些测量折射率的方法中，最重要的是最小偏向用法和V棱镜法。推导最小偏向角法和V棱镜法的所有文献都沿用经典的原理公式，而这些经典的原理公式没有考虑到空气实际折射率对被测试样折射率的影响。

In this paper we have point out the error of principle formula quoted by all literatures at home and abroad to measure the refractive angle and the method of V-prism, derive from beginning the right formula of measuring refractive index by the method of minimum deviation angle and the method of V-prism.

本文指出了测量光学材料折射率的最小偏向角法和V棱镜法国内外所有文献的原理公式误差，重新推导了最小偏向角法和V棱镜法测量折射率的正确公式。基于最小偏向角法用精密测角仅可以获得±3×10-6的折射率的测量精度，然而，这些文献沿用经典的测量原理公式却具有-4×10－4数量级的原理公式误差，因此导致错误的测量结果。

Based on the method of minimum deviation angle, man can obtain the accuracy of measuring refractive index of glass at 3×10-6 with fine apparatus for measuring angle, but the classical princip1e formula quote...

计算表明，用经典公式计算标准试样折射率虽然对光学系统象差影响很小，但作为折射率基准测量，这样大的原理公式误差是不允许的。

Initially the following measures are taken for association of the angle positions to physical reflectors, and for determination of the position of the vehicle (10): i at least three angle values with a suitable distribution over the search sector is selected, ii the angle values are associated to reflectors and a position is determined for the vehicle on the basis of the known position of the assumed reflectors, iii if the vehicle position determined in this way is within a certain part of the transport area the other angle values are associated to reflectors, iv for each angle value, existing deviation is determined between detected angle values and angle values expected between the vehicle position and known reflectors, v the measures taken are repeated for each possible combination of selected angle values.

最初使用下列步骤使这些角位与反射器关联以便确定车辆（10）的位置：i）在该搜索扇形上选择至少三个合适分布的角度值，ii）使各角度值与各反射器关联，根据假设反射器的已知位置确定车辆的位置，iii）如果如此确定的车辆位置在该运输区的某一部分中，则使其他角度值与反射器关联，iv）对于每一角度值，确定所检测角度值与车辆位置与己知反射器之间预期角度值之间的偏差，v）对于所选择的角度值的每一种可能组合反复进行这些步骤。

So in order to improve ROP, the VTK vertical drilling technology of Baker Hughes was introduced. VTK is a kind of closed loop, automatic, and vertical drilling technology, made up of closedloop rotary steering drilling system AUTOTRAK, highperformance X-TREME motor and reliable MWD. It is able to return the well path back to vertical by adopting downhole microprocessors to analyze the measured deviation data and determine the proper force necessary for decreasing the deviation angle to guide the steering rib at the highside to reliably stick out against the upper wellbore.

为提高机械钻速，引进贝克休斯的VTK垂直钻井技术，它是由AUTOTRAK、高性能X-TREME马达、可靠的MWD三种技术开发出来的一种闭环自动垂直钻井技术，能够根据井眼的偏斜，经井下微处理器分析判断，使导向稳定地靠近井眼高边方向导向肋板伸出顶向上井壁，这样使钻头产生合理的降斜力，从而使井眼回到垂直轨道上来。

So in order to improve ROP, the VTK vertical drilling technology of Baker Hughes was introduced. VTK is a kind of closed loop, automatic, and vertical drilling technology, made up of closed loop rotary steering drilling system AUTOTRAK, high-performance X-TREME motor and reliable MWD. It is able to return the well path back to vertical by adopting downhole microprocessors to analyze the measured deviation data and determine the proper force necessary for decreasing the deviation angle to guide the steering rib at the high-side to reliably stick out against the upper wellbore.

为提高机械钻速，引进贝克休斯的VTK垂直钻井技术，它是由AUTOTRAK、高性能X-TREME马达、可靠的MWD三种技术开发出来的一种闭环自动垂直钻井技术，能够根据井眼的偏斜，经井下微处理器分析判断，使导向稳定地靠近井眼高边方向导向肋板伸出顶向上井壁，这样使钻头产生合理的降斜力，从而使井眼回到垂直轨道上来。

At present, the location of the anti-lopsided wear centralizer used in fields is mainly based on the deviation angle. In fact, lopsided wear may be caused by the change of azimuth angle or by the vertical well section and hold angle section during the working of the bucket rod.

目前油田矿场主要根据井斜角来确定防偏磨扶正器下入位置，实际上方位角变化也能导致偏磨，抽油杆杆柱在运动过程中直井段和稳斜段也会产生偏磨。

Faults : Slight deviation of the angle of the shoulder articulation. Feet slightly toeing in or out, pasterns a little soft.

缺点：肩部连接的角度有略微偏差，脚尖轻微向内或向外，骹骨略微软。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐