查询词典 angle gear

From say on the whole, bump deep increase as what bump force and increase, anti-impact gear is bumped in resistance when, steel tube rises to basically be sucked can action, the suction of angle iron can be worth the 1/5 that is steel tube about.

从总体上说，撞深随着撞击力的增加而增加，防撞装置在反抗撞击时，钢管起到主要吸能的功能，角钢的吸能值约为钢管的1/5。

Such as angle grinder, wire brush, needle beam pneumatic rust, and wind knock rust hammers, gear-type rotary rust, etc., are semi-mechanized equipment, tools, light, mobility, and to more thoroughly to rust , old coatings, the coating can be played on the shelf hair treatment, significantly more efficient than manual derusting increased up to 1 ~ 2m2 / h, but can not remove the oxide skin, the smaller surface roughness and can not achieve high-quality surface to deal with quality, ergonomic handle lower than the jet.

如角向磨光机、钢丝刷、风动针束除锈器、风动敲锈锤、齿型旋转除锈器等，属于半机械化设备，工具轻巧、机动性大，能较彻底去除锈、旧涂层等，能对货架涂层进行打毛处理，效率比手工除锈大大提高，可达1~2m2/h，但不能除去氧化皮，表面粗糙度较小，不能达到优质的表面处理质量，工效较喷射处理低。

However, if the bevel angle of the gear approaches to 90 °, it is difficult to machine it.

但是，如果直齿锥齿轮的锥角接近90度，利用伞齿刨加工是非常困难的。

Although bevel gear are usually made for a shaft angle of 90 deg.

虽然锥齿轮通常为定轴角为90度。

It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

论文摘要：分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定，珩磨轮的节锥面由珩磨轮齿数以及公法线和与珩磨轮及被珩磨齿轮的轴线平行的平面的夹角两个参数所确定。

In order to solve the theoretical backlash problem of the teeth, which is crucial to the number of actual contact pairs of teeth in the research on multi teeth contact of crown gear coupling , the theoretical backlash of teeth flank with the concept of backlash angle is first time defined and described in the paper, and the minimization model of its variables is set up.

为解决鼓形齿联轴器多齿接触研究课题中的实际接触齿对数的关键技术轮齿理论间隙的问题，首次用间隙角的概念对轮齿理论间隙作了定义和描述；建立了该变量的极小化模型；对一鼓形齿联轴器作了实际优化计算，得出了鼓形齿联轴器多齿接触研究中计算实际接触齿对数所需的不同啮合状态下的最小间隙角

The features of this dissertation are lie in: a The concept of"Influence Distance"was presented to quantitatively express"corner effect", systematicly studied on the influence of all factors on"influence distance". It could provide reference to angle designing from the view of heat treatment; b Deeply studied on the influence of shape factor to carbon concentration field. It could provide reference to gear designing from the view of heat treatment; c New model was set up to describe the two-dimensional concentration field of carbide dispersion carburizing. The shortcomings of"effective diffusion constant method"and"equilibrium constant method"were overcome in this model.

本文的特色在于：①提出了用"尖角影响距离"定量描述"尖角效应"的方法，并系统研究了各种因素对"尖角影响距离"的影响规律，从热处理角度为工件尖角部位的设计提供依据；②首次深入研究了齿轮的各种形状因素对浓度场的影响，从热处理角度为齿轮设计提供依据；③建立了能够更有效地模拟过饱和渗碳浓度场的数学模型，该模型克服了"有效扩散系数法"及"平衡常数法"的不足，与"最小自由能法"可互为补充。

However, when the helix angle are not equal, the gear with the larger helix angle should be used as the driver if both gears have the same hand.

但是，当螺旋角不相等，则齿轮与大螺旋角应作为司机，如果这两个齿轮具有相同的手。

The results indicate that the oil-film thickness increases with the increase of normal modulus and it decreases with the increase of gear width,helix angle and normal pressure angle while the transmission ratio changes.

在斜齿圆柱齿轮的啮合过程中，由于每个瞬时沿齿面接触处的曲率半径、表面速度和载荷等参数均不同，所以该过程是动态的。

However, when the helix angle are not equal, the gear with the larger helix angle should be used as the driver if both gears have the same hand.

然而当该齿的斜角不相等时，如果两个齿轮具有相同齿向的话，大斜角齿轮应用作主动齿轮。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。