查询词典 angle gear

In the 无效,,It is a main fact respectively, circumference Li of the driven gear;,It is a main fact respectively, the spiral angle of the driven gear.

主减速器的结构形式主要是根据齿轮类型，减速器形式不同而不同。

Bookbinder book bevel gear is a piece of steel angle and a bakelite bevel gear, drive out all of the roll out of the book.

胶订机出书伞齿轮是一件钢伞齿轮和一件胶木伞齿轮，传动出书的所有出书辊。

Right angle bevel gear reducer of the B series, concentric shaft bevel gear reducer of the H series, no paragraph series variable speed reducer.

直角斜齿轮减速机的B系列、同心轴伞齿轮减速机的H系列，无段变速减速机系列等。

Therefore, the face-width of the face gear is limited. According to the conditions of undercutting and pointing, the formulae of minimum inner diameter and maximum outer diameter are derived for the shaft angle face gear .

根据产生根切与齿顶变尖的条件，给出了任意轴交角下齿宽设计的公式，定义了两个无量纲参数，即最小内半径系数和最大外半径系数，来表示齿宽的设计范围。

Key products include: cast iron plate, cast iron platform, the test platform, crossed platform, Maohan platform, fitter platform, table, Ping-foot, to me, V-type, V-iron, right-angle-foot, V-iron, foot bridge , Curved panels, machine damping Sizing Block, adjusted Sizing Block, partial-place, Jack, special wrench, gear Gear beat Tester; platform granite, marble slab, Ping-foot, V-iron, to me, Jiaochi, V-shaped blocks, such as platform support.

主要产品包括：铸铁平板、铸铁平台、检验平台、划线平台、铆焊平台、钳工平台、工作台、平尺、方箱、V型架、V 型铁、直角尺、V型铁、桥尺、弯板、机床减震垫铁、调整垫铁、偏摆仪、千斤顶、特种扳手、齿轮齿圈跳动检查仪；花岗石平台、大理石平板、平尺、V型铁、方箱、角尺、V型块、平台支架等。

Lock angle in the design and the cone has made the appropriate choice, cone friction that makes the engagement ring gear tooth sets and the rapid synchronization, and will produce a Lock role and to prevent the gear before engaging in sync.

锁止角与锥面在设计时已作了适当选择，锥面摩擦使得待啮合的齿套与齿圈迅速同步，同时又会产生一种锁止作用，防止齿轮在同步前进行啮合。

According to the design principle and basic characteristic of the gear shaper cutter , its rake angle and top face are adjusted, and the cutter blade projection on the datum plane is modified appropriately to finish the profile modification of K-teeth in gear shaper cutting process.

针对插齿加工过程中K形齿的修形问题，根据插齿刀的设计原理和基本特点，提出了以改变插齿刀的前角和前刀面形状来改变切削刃在其基面上的投影，达到在插齿加工中对齿形的修形的目的。

The helix angle is the same on each gear, but one gear must have a right-hand helix and the other a left-hand helix.

该螺旋角是一样的，每个齿轮的，但其中一个齿轮必须有一个右手边的螺旋和另一人左手螺旋。

The helix angle is the same on each gear, but one gear must have a right-hand helix and the other a left-hand helix.

螺旋角度是相同的在每个之上齿轮，但是一齿轮一定有一个用右手的螺旋和另一个一个左侧的螺旋。

The points-line meshing gear is different from involute gear in choice of helix angle.

点线啮合齿轮螺旋角β的选择，改变了渐开线齿轮为凑中心距或者从优化角度来选取β值的情况。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。