查询词典 angle gear

The company produces the processing equipment to be advanced, check-out facility excellent, has the numerical control lathe, the numerical control drilling machine, the machining center, the numerical control gear-hobbing machine, the gear shaper, the fine borer, the universal milling machines, each kind of grinder, the table planer, the booklet bender, the large-scale lathe, the mechanical slicer, high intermediate frequency quenching, the well type, the box-type hardening furnace, the tempering furnace, the automatic welding machine, the X-ray crack detection machine, the cloth, the Rockwell tester; Electric hoist test platform, sound-level meter, varnish film thickness gauge, altazimuth, level; The material analysis laboratory, the metallography analysis room and so on full had guaranteed strictly the vehicle, the mill, dig, rub, pull, the boring, to drill, the ramming, cutting, the angle iron, the chemical examination and the heat treatment and so on complete technical process.

公司生产加工设备先进，检测设备精良，拥有数控车床、数控钻床、加工中心、数控滚齿机、插齿机、精密镗床、万能铣床、各种磨床、龙门刨床、折弯机、大型车床、刨床、高中频淬火、井式、箱式淬火炉、回火炉、自动焊机、 X射线探伤机、布、洛氏硬度计；电动葫芦试验台、声级计、漆膜测厚仪、经纬仪、水准仪；材料分析化验室，金相分析室等充分严格保证了车、铣、刨、磨、拉、镗、钻、冲压、切割、弯板、化验及热处理等全部工艺流程。

Aiming at the signal processing problems that exist in online fault diagnosis for train running gear, based on discussing the principle of characteristic spectrum analysis, a method of full period and uniform angle sampling is applied, which transfers the vibration signal from time domain into angular domain. The angular domain signal is transferred into corresponding characteristic spectrum using FFT. Through spectrum estimation and analysis, fault characteristic spectrum values of running gear components are acquired to distinguish their faults.

在讨论特征分析方法原理的基础上，针对机车走行部故障在线监测过程中存在的信号分析与处理问题，运用整周期等角度采样方法将时域振动信号转换为角域信号，采用FFT变换将角域信号变换为对应的特征频谱，通过谱估计、谱图分析得到机车走行部各零部件的故障特征谱值，再根据该特征谱值识别机车走行部各零部件的故障。

Analyzing the honing principle of spiral bevel gears based on crossing-axis transmission, the mathematical model of the relative sliding speed of the contact point between honing wheel and gear is achieved. It is determined that the pitch cone of honing wheel depends on the number of teeth in the honing wheel and the angle between the common normal of pitch cones and the plane parallel to both gear and honing wheel axes.

分析了基于交错轴传动的珩齿原理，导出珩磨轮与被珩齿轮在啮合点处的相对滑动速度的数学模型，根据该数学模型可以判定珩磨轮的节锥面是由珩磨轮齿数、公法线和与珩磨轮轴线平行的平面夹角所确定。

This is because the angle on the worm is so shallow that when the gear tries to spin it, the friction between the gear and the worm holds the worm in place.

这是因为，蜗轮蜗杆的升程角很小，当涡轮要带动蜗杆时，蜗轮蜗杆间的摩擦力把蜗杆锁住了。

Rossi can offer a wide range of products including parallel, right angle and coaxial shaft gear reducers and gear motors, worm and planetary ones.

公司可以提供的产品范围非常广阔，其中包括：平行轴，直角轴，同轴减速机及减速电机，蜗轮蜗杆及行星系列。

The experiment result has proved that the gear transmission error will be increased due to the gear crossed angle increased.

实验结果已证实齿轮传动误差会随齿轮轴交角之增大而增大。

Because of this, it is usual to specify the lead angle on the worm, which is the complement of the worm helix angle, and the helix angle on the gear; the two angles are equal for a 90-deg.

正因为如此，它通常指定牵头角度对蠕虫，它是相辅相成的蠕虫螺旋角，螺旋角对齿轮；两个角度来看都是平等的，为90摄氏度。

When turning gear from middle to maximum angle of steering gear, the suction and outlet pressure must be attention.

在将舵从中位转至最大舵角时应注意进，回油油路压力值。

Because of this, it is usual to specify the lead angle on the worm, which is the complement of the worm helix angle, and the helix angle on the gear; the two angles are equal for a 90-deg.

因为这，叙述是平常的那领引角度在虫上，是那补足物虫螺旋角度，和螺旋角度在那之上齿轮；二个角度是对手为 90 deg 。

In this research, transmission error tests and analyses under center distance variations and different gear crossed angle for spur gear pairs are also performed and received substantial results.

本研究也分别进行了不同中心距对齿轮传动误差之影响实验及不同轴交角对齿轮传动误差之影响实验，亦已有具体结果。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。