查询词典 angle bar

METHODS: The endodontic instrument was assumed as a metal conical bar. The normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics. The relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, and metal elastic modulus were analyzed. The criteria for yielding and fracture of the instrument were discussed.

将根管器械刃部假设截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

METHODS: The endodontic instrument was assumed as a metal conical bar, the normal stress of bending loads and the shear stress of torsional loads were calculated with the knowledge of mechanics , the relations between stress and such parameters as angle and radius of canal curvature, radius of instrument, polar moment of inertia, metal elastic modulus were analyzed, the criteria for yielding and fracture of the instrument were discussed .

将根管器械刃部假设为截面为圆的金属细锥杆，利用材料力学及断裂力学的原理与方法，分别计算根管器械在弯、扭载荷下的应力分布，分析应力与根管弯曲角度、根管弯曲半径、器械直径、器械横截面极惯性距、金属弹性模量等参数的确切关系；探讨器械屈服、断裂失效的准则。

If you're using your speed bar or your trimmers are out and fast, be aware that you're new angle of attack generally _increases_ your risk of collapse or front tuck.

如果你正在使用脚蹬式加速棒或调速器加速飞行，要清楚你的伞翼正处于一个新的攻角下，通常会增加进入夹叶或前扣的危险。

Before construction starts, make ready the following tools: nail hammer, wrench, hammer, saw, wire plumps, ink fountain, electric drill, steel rule, angle, level bar, portable electric saw, portable electric plane.

施工前准备好钉锤、扳手、榔头、锯子、线锤、墨斗、电钻、钢尺、角尺、水平尺、手提电锯、手提电刨等。

The objectives of this paper were to investigate the simulation and design of continuous multiple-station rolling forming process for a U-Section Steel Bar by CAE software-DEFORMTM Due to the limitation of elements number using a short strip 120mm went through all the stations to simulate the real continuous rolling forming on factory The roller gap was fixed as 0 30mm roll speed was 20 rad/sec and progressive angles were all equal for each rolling process which were the formed angle divided by by the number of station Three rolling processes were selected with 6 9 and 12 stations respectively During simulation processes two cases occurred Case A the strip was through a single station Case B the strip across two stations Because the strip laterals side was stretched and twisted during the process The model of case B closer to the practical process than case A and the calculated stress and strain on the tip of U section for case A were lower than these for case B by up to 15% From the result of case B for each process the stress for 12-station process was smallest 9-station process second and 6-station process next Because less-station can save larger cost and forming time but the bigger stress and strain for 6-station caused wrinkles on lateral sides not found on 9-station and 12-station Therefore 9-station process was a more suitable design than 12-station process smaller stretched and twisted and stress The progressive angles for 12-station was 7 5?

本文主要是以DEFORMTM有限元素软体模拟U型钢片连续道次成型与单一道次成型以确认单一道次模拟的是否可取代连续道次模拟之研究。因DEFORMTM 软体对於网格元素上的限制故使用较短素材120mm通过所有的成型站以模拟工厂实际连续成形方法。辊轮间隙固定为0 3mm；辊轮转速为20 rad/sec；弯曲角度的方法为将成型角度平均除以成型站数。有三种辊轮成型方式被选择分别为6站，9站，与12站。在模拟的过程中有两种现象会产生 Case A，素材通过单一成型站。Case B，素材会通过两个成型站。因为在模拟过程中素材的两端会有拉应力与扭力。Case B的模拟比Case A像实际的制程，并计算应力与应变在U型断面的Tip部中可发现Case A比Case B低约15%。从Case B的每站的结果可以得知，12站的成型应力最小，9站次之，6站最后。

The company possess a continuous bar rolling line of 350,000 tons annual output and an angle steel line of 100,000 tons.

公司生产的各种规格钢材常年销往华东地区及京津冀鲁地区，在用户中享有较高的声誉。

Range of Products: steel, flat steel, square steel, angle steel, channel steel, steel plate, corrugated steel bar, welded tube, steel tube, galvanised zinc coil plate with a zinc coating and other custom-made steel products.

本公司以诚信经营，客户至上，服务周到，合理价格作为经营宗旨。经营范围：定做各种规格冷拉。热轧的特种扁钢、方钢、角钢、槽钢、焊管、圆钢等可根据用户需要代订购特殊规格的钢材。

Supporting the 8 inner stay bar with the top frame on around of the tower body as the same horizontal position, press the master chord of the tower body tightly, work in the tower head part of the climbing frame and adjust the vertical angle less than 4/1000 of the tower body.

7.4.7 将 8 根内撑杆支撑在与最上面一个框架位于同一水平的塔身四周，适当顶紧塔身主弦，配合爬升框架上的顶块调整塔身的垂直度至 4/1000 以内，然后，适当顶紧上面两框架的顶块，锁住顶块螺母。

It equipped with debugging interface,operation interface,fuel pump parameter interface,and word illustration interface. Advanced angle, rotate speed, count, fuel oil temperature and so on could be displayed on the screen( Oil pressure, atmospheric pressure, rack bar stroke are optional). It can beinput fuel pump debugging data manually,print and save it.

备有喷油泵所有调试界面、操作界面、油泵参数界面及文字说明界面，实现提前角、转速、计数、燃油温度等一系列功能全部屏显（油压、气压、齿杆行程可选装），并可通过人工输入，打印并保存油泵调试数据。

The brown- envelope whip-round has become as common as the printer jam, gift shops are overcrowded with leaving cards the size of Japan (to accommodate hundreds of straining-to-be- witty messages written at an angle), and every corner of every bar on every Friday night is occupied by a gaggle of suits and skirts saying farewell to someone whose name they can barely recall.

装着大家凑份子钱的牛皮纸信封，已变得像打印机被卡住一样普遍；礼品店里摆满了日本版图一样的离别卡片（这是为了装得下同事们写在卡片角落里、拼命显得很睿智的数百条留言）；每个周五晚上，每个酒吧的每个角落里，每个身着西装和套裙的男男女女，都在吵吵嚷嚷着挥别某个他们可能连名字都叫不上来的同事。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了