查询词典 alloy

The results show that constitutional phases in the 〓 alloy is the same as that in the 〓 alloy, but phase composition and transformation temperatures of two alloys are quite different. The Ms temperature of the 〓 alloy is lower than-180℃. In order to enable the alloy to be used for making pipe couplings, it is necessary to control Al addition and to increase Ti addition in the alloy. In the 〓 alloy, there exist three constitutional phases: TiNi matrix phase with B19′structure,β-Ta phase and NiTa〓 phase. Transformation temperatures, M〓, Ms, As and A〓, of the alloy are 55℃, 66℃, 94℃ and 109℃, respectively.

结果表明，〓合金显微组织的相组成物与〓合金一样，但相成分明显不同，相变温度相差较大，其Ms温度低于-180℃，要想使该系合金用于制作记忆合金管接头，必须控制铝的添加量并提高合金中的钛含量使合金的Ms温度控制在-80℃～-100℃之间；〓合金是由具有B19'结构的TiNi基体相、β—Ta固溶体和NiTa〓化合物三相组成的，其相变温度M〓、Ms、As和A〓分别为：55℃、66℃、94℃和109℃。

Alloy frame, Double Wall Alloy tire circle, Dishing brake, forging suspension front fork, Alloy adjustable handlebar stem with gears, alloy handle, alloy retroflex saddle tube, alloy adjustable rack, middle parking rack, Alum-plating electric mudgurads, alloy cranks, 1.75 glisten tires. SHIMANO 6-speed chains linker, SHIMANO gearlever, spring saddle,24V.9AH/13AH battery, intelligent meterplate, LED front and rear lights, 3-grade Electric Assist Driving System（1st,Bike;2nd,1:1 Standard Riding Pull-assist; 3rd,Strong Pull-Assist） 6-grade Manual speed changes,1.8A NiMH Battery chargerAlloy Power-cut Brake handle

描述： 6061#铝合金高强度车架，铝双层车圈、前后碟刹、铝前花鼓、锻造铝合金减震前叉、有牙铝合金把立、铝合金把横、铝合金翻转鞍管、铝合金可调节衣架、中支撑、铝合金曲柄，镀铝导电型前后泥板、1.75反光轮胎、禧玛诺外6速拨链器、禧玛诺变速杆、弹簧减震坐垫、9AH/13AH镍氢电池、智能仪表盘、LED照明前灯、后LED灯、三档电动助力驱动系统（一挡、自行车；二挡、1：1标准骑行助力；三挡、强助力）、6档机械变速、1.8A镍氢电池充电器、全铝断电刹车握把。

The results show that:(1) after MA for 20h, single phase bcc nanocrystalline supersaturate solid solution formed in Fe84Nb7B9 and Fe80Ti8B12 alloys; the thermal stability of nanocrystalline microstructure in Fe80Ti8B12 alloy was improved significantly than that in Fe84Nb7B9 alloy, and the decomposition temperature of supersaturate solid solution decreased in Fe80Ti8B12 alloy.(2) under 30MPa/900℃/0.5h hot-press sintering conditions, the relative density of Fe84Nb7B9 and Fe80Ti8B12 bulk alloys were 96.7% and 95.5%, respectively. Compared with Fe84Nb7B9 alloy (muti-phase microstructure), Fe80Ti8B12 alloy was composed of superfine crystalline (50~200nm) of single phase α-Fe;(3) the magnetic properties of Fe80Ti8B12 bulk alloy σ(subscript s=198.6emu/g, H=54.6Oe were more excellent than that of Fe84Nb7B9 bulk alloy σ(subscript s=162.9emu/g, H=105.1G, it was related to the different phases formed during hot-press sintering and the grain size of nanocrystalline powder.

结果表明：(1)20hMA后，Fe84Nb7B9和Fe80Ti8B12均形成了单相bcc纳米晶过饱和固溶体，相对前者，后者纳米晶组织热稳定性明显提高，过饱和固溶体相分解温度略有降低；(2)在30MPa/900℃／0.5h热压条件下，Fe84Nb7B9和Fe80Ti8B12块体合金相对密度分别为96.7%和95.5%，相对前者，后者由超细晶(50~200nm)单相α-Fe组成；(3)Fe80Ti8B12块体合金软磁性能σ(下标 s=198.6emu/g，H＝54.6Oe明显高於Fe84Nb7B9块体合金σ(下标 s=162.9emu/g，H＝105.1Oe，此与纳米晶粉末在热压烧结过程中所形成相的种类和晶粒尺寸大小有关。

Stainless steel concave end knurling;DIN915 Stainless steel cylindrical end; DIN914 Stainless steel pointed end; DIN916 Stainless steel concave end; DIN913 Stainless steel flat end; DIN551 Stainless steel slotted point; DIN906 Stainless steel oil plug,semi-circular; Stainless steel two-end hexagonal non-standard; Brass internal hexagonal,cross,non-standard; Brass wobbler,nickel-plated; Stainless steel ,alloy steel heat-resistant; Alloy steel zinc-plated; Alloy steel semi-circular; DIN915 Alloy steel cylindrical end, Philips screw non-standard; DIN916 Alloy steel concave end;DIN914 Alloy steel pointed end;DIN906 Alloy steel oil plug; Corrugated ball; Two-end internal hexagonal non-standard; Textile machine screw-nail; Tool-post screw-nail

不锈钢凹端滚花；DIN915 不锈钢柱端；DIN914 不锈钢尖端；DIN916 不锈钢凹端；DIN913 不锈钢平端；DIN551 不锈钢一字槽；DIN906 不锈钢油塞、半圆；不锈钢2头内六角非标；黄铜内六角、十字槽、非标；黄铜梅花头、镀镍；不锈钢、合金钢耐落；合金钢镀锌；合金刚半圆；DIN915 合金钢柱端、十字槽、非标；DIN916 合金钢凹端；DIN914 合金钢尖端；DIN906 合金钢油塞；波珠；2头内六角非标；纺织机螺钉；刀架螺钉。

Electrochemical measurements of the singler A2B7 and A5B19 phase alloy showed that, the activation properties of singler type A2B7 and AsB19 phase composition alloys were the same. The maximum discharge capacity (386.12mAh/g) of A2B7 type phase alloy was slightly higher than the maximum discharge capacity (371.38mAh/g) of A5B19 type phase alloy. The cyclic stability of alloy electrode of both A2B7 and A5B19-type phase alloy were all very well. The capacity retention rate of 100 cyclic was more than 85%.The high-rate discharge (HRD900=85%) of AsB19phase alloy was higher than the high-rate discharge (HRD900=76.6%) of A2B7phase alloy.

对较单一的A2B7与A5B19型物相合金进行电化学测试，结果表明：A2B7型相结构储氢合金的活化次数与A5B19型相结构储氢合金的活化次数基本相同，A2B7型物相合金的最大放电容量(386.12mAh/g)略高于A5B19型物相合金的最大放电容量(371.38mAh/g)。A2B7与A5B19型物相合金电极100个循环容量保持率都在85%以上，且差别不大。A5B19型相结构合金的高倍率放电性能(HRD900=85%)高于A2B7型相结构合金的高倍率放电性能(HRD900=76.6%)。

Alloy frame, Double Wall Alloy tire circle, Dishing brake, forging suspension front fork, Alloy adjustable handlebar stem with gears, alloy handle, alloy retroflex saddle tube, alloy adjustable rack, middle parking rack, Alum-plating electric mudgurads, alloy cranks, 1.75 glisten tires. SHIMANO 6-speed chains linker, SHIMANO gearlever, spring saddle,24V.9AH/13AH battery, intelligent meterplate, LED front and rear lights, 3-grade Electric Assist Driving System（1st,Bike;2nd,1:1 Standard Riding Pull-assist; 3rd,Strong Pull-Assist） 6-grade Manual speed changes,1.8A NiMH Battery chargerAlloy Power-cut Brake handle

描述： 6061#铝合金高强度车架，铝双层车圈、前碟刹、铝前花鼓、锻造铝合金减震前叉、有牙铝合金把立、铝合金把横、铝合金翻转鞍管、铝合金可调节衣架、中支撑、铝合金曲柄，镀铝导电型前后泥板、1.75反光轮胎、禧玛诺外6速拨链器、禧玛诺变速杆、弹簧减震坐垫、9AH/13AH镍氢电池、智能仪表盘、 LED照明前灯、后LED灯、三档电动助力驱动系统（一挡、自行车；二挡、1：1标准骑行助力；三挡、强助力）、6档机械变速、1.8A镍氢电池充电器、全铝断电刹车握把。

At present, we offer high quality high proportion fishing fall, high proportion alloy ball, high proportion alloy round stick, high proportion alloy unit, high proportion alloy golf head, high proportion alloy off-centered dipole and other high proportion alloy abnormal units. Production capacity: above 200T/year.

按合金组成特性及用途分为W-Ni-Fe、W-Ni-Cu、W-Co、W-WC-Cu、W-Ag等主要系列，其密度高达16 。5-19.0g/cm3，而被世人称为高比重合金，它还具有一系列优异的特性，比重大：一般比重为16.5-18.75g/cm3，，强度高：抗拉强度为700-1000Mpa，吸收射线能力强：其能力比铅高30-40%，导热系数大：为模具钢的5倍；热膨胀系数小：只有铁或钢的1/2-1/3，良好的可导电性能；具有良好的可焊性和加工性。

Moreover, the hot compressive deformation behavior of the RS/PM AZ91 magnesium alloy and AZ91 alloy matrix composite were also investigated, the conclusions are drawn as follows:1. The processing parameters of the atomization-twin rolls quenching technology were optimized as follows: the diameter of the nozzle 1mm, the wheel velocity 25m/s, the pressure of atomization gas 0.3MPa and Ar gas for melt injection 0.1MPa. The RS AZ91 alloy flakes exhibited fine and uniform microstructures. When the flakes were extruded at 673K, extruded velocity of 0.1mm/min and extrusion ratio of 25:1,the magnesium alloy rods with clean surface, uniform dimension and excellent mechanical properties were obtained.2. The RS AZ91 magnesium alloy powders prepared by atomization-twin rolls quenched technology exhibited fine equiaxed grains with the grain size of 1-3μm, the phase constituent included supersaturate solid solution phaseα-Mg and miner fineβ-Mg_(17)Al_(12) phase. The as-extruded materials also exhibited equiaxed grains with the size of 5-7μm and a large number of fineβ-Al_(12)Mg_(17) and fewer AlMg_2Zn phases were detected in the alloy.

本文还研究了快速凝固/粉末冶金AZ91镁合金热压缩变形流变应力行为，快速凝固/粉末冶金法原位生成Mg_2Si增强AZ91镁基复合材料，经过系统的研究，获得如下结论：1、雾化-双辊急冷法在下列工艺参数组合下：双辊线速度25m/s；喷嘴直径1mm；熔体压射压力0.1MPa；雾化气体压力0.3MPa。，可获得宏观尺寸细小、微观组织均匀细小、综合性能优良的的快速凝固AZ91镁合金细碎箔带，快速凝固箔带在挤压温度为673K、挤压速度为0.1mm/min，挤压比为25：1时，可获得的外表光洁、尺寸均匀、组织性能优异的镁合金棒材。2、雾化-双辊急冷法制备的AZ91镁合金粉末态为细小等轴晶组织，晶粒尺寸1-3μm，组织为α-Mg过饱和固溶体和微量的细小β-Mg_(17)Al_(12)相组成；粉末挤压棒材为等轴晶组织，晶粒尺寸5-7μm，组织中含有大量细小的β-Al_(12)Mg_(17)以及AlMg_2Zn析出相，室温力学性能，抗拉强度383MPa，屈服强度275MPa，断后伸长率7.5%。

The results show that Fe0.13[Co20Ni80]0.87 alloy fibers are characterized with thin diameters between 0.3 and 2.0 μm, with high aspect ratio, dense and smooth surfaces. The crystalline size of the alloy fibers are mainly influenced by the thermal reduction temperature and are in the range of 20 to 50 nm with a corresponding reduction temperature range of 300 to 700 ℃. The magnetic properties of the alloy fibers are largely affected by the carbon content and crystalline sizes of the alloy fibers. With increasing thermal reduction temperature, the coercivity decreases while the saturation magnetisation value of the alloy fibers dramatically increases at lower reduction temperatures. The alloy fibers prepared at reduction temperature of 700 ℃ have a saturation magnetisation value of 120 Am2/kg and a coercivity value of 10.4 kA/m, respectively.

结果表明：Fe0.13[Co20Ni80]0.87合金纤维的直径为0.3~2.0 μm，表面光滑、长径比大；组成合金纤维的晶粒大小与还原温度密切相关，当温度为300~700 ℃时，晶粒尺寸由约20 nm增加到约50 nm；该合金纤维显铁磁性，其矫顽力主要受合金中C含量及晶粒大小的影响，随制备温度的升高而降低；饱和磁化强度则主要与合金的组分相关，随还原温度的升高和合金纯度的提高而增大；经700 ℃热还原后，合金纤维的饱和磁化强度 m s为120 Am2/kg，矫顽力 H c为10.4 kA/m。

The results show that the dissolution process of prefabricating alloy can be divided into two periods when the temperature of zinc melt is below the melting point of aluminum.Firstly,zinc melts infiltrates into the prefabricating alloy and then Zn-Al-TiC alloy forms in the surface layer of the prefabricating alloy.Secondly,the Zn-Al-TiC alloy of this alloy surface layer begins to dissolve to the zinc melt.

结果表明：当锌熔体温度低于铝熔点时，预制合金的溶解可分为两个阶段：第一阶段为液态锌向预制合金中浸渗，并在预制合金表层内形成Zn-Al-TiC合金；第二阶段为预制合金表层内的Zn-Al-TiC合金开始溶解并进入锌熔体。

Objective To study the effect of chitosan in the prevention of fibrous scar formation in the epidural space after laminectomy.

目的 观察选择性脊神经后根切除术椎板切除后硬膜外几种防瘢痕粘连物质的作用并探讨其机制。

On his way to the lift, he looked back to us or was it me his eyes pointing?

当他要进电梯时，他回头看我们（或者说是我，他的眼光？