英语人>网络例句>allowable value 相关的网络例句
allowable value相关的网络例句

查询词典 allowable value

与 allowable value 相关的网络例句 [注:此内容来源于网络,仅供参考]

First, the overall satisfaction membership function of the group decision making is defined based on the allowable error given by the decision-maker respectively. Following that, a weight model is suggested for finding the maximal degree of the group preference satisfaction. Based on the suggested model, the consistency degree of the group preference is defined. Then, an alternation approach is proposed to improve the judgment of the low consistency degree of the decision-maker.

基于决策者给出的允许偏差,定义了群决策满意度隶属函数,建立了求解群体偏好满意程度最大化的权重模型,提出了群体偏好一致性程度的衡量指标,研究了对一致性程度较差的决策者判断进行交互调整的方法。

Examinations of steady status and analysis of dynamic experiments have been conducted on Band-Tube evaporator and Parallel-Flow condenser using R134a refrigerant. The steady examination show that the model error was under the allowable error, The inlet mass and enthalpy disturb experiments indicate that the subsection model ,be good at reflecting the change of parameters of the heat exchanger, accord with the basic principle of thermodynamics theory and the actual work status.

在进行仿真试验时,以使用R134a作制冷剂的管带式蒸发器和平行流式冷凝器为对象,完成了稳态仿真计算、试验和动态仿真分析,稳态计算结果和试验数据对比表明,其误差在允许范围内;进口质量和焓值的扰动试验结果表明:本文所建的区段式换热器仿真模型,能很好的反映换热器性能参数的动态变化,与系统热动力学理论和冷凝器、蒸发器的实际工作过程基本一致。

Through the characteristic experiment to five PVC filmducts with different hole spacing,a series of design parameter was recom-mended under the allowable error(±10%)of hole discharge air volume per u-nit lengh.

通过在鸡舍环境下对五组不同孔口分布的带孔PVC风管的送风均匀性试验,推荐了在孔口气流一致性偏差允许范围内(±10%)带孔PVC风管的工程设计参数。

First, the uncertain ordered weighted averaging is used to aggregate the decision-maker's different preference information into the interval number comparison matrix. Then, the group's overall satisfaction membership function is defined based on the decision-making's allowable error. The maximal group consistency weight model is established.

采用UOWA算子将决策者的偏好信息集结为区间数互反判断矩阵和互补判断矩阵两种形式,结合决策者给出的允许偏差,定义群满意度隶属函数,建立求解群偏好一致程度最大化的权重模型。

Results: The imprecision of six diluent concentrations in duplicate was 2.68%, the best fit model was the cubic equation. The deviaton from linearity of the first concentration was 42.3%, exceeding the 5% clinical allowable error. DLs of the other concentratons were within limit.

结果:六个稀释浓度样本重复测定的不精密度为2.68%,三次多项式为最适拟合模型,第一个稀释浓度的非线性程度达到42.3%,超过5%的允许范围,为临床不可接受,其它五个稀释浓度的线性偏离均在允许范围内。

Examination found a number of major quality problems: First, part of the observed deformation and deformation measurements are not laying a solid reference point, deformation monitoring points do not comply with regulatory requirements; deformation observation, the calculation is not strictly enforce the state standards, such as the base network is not on a regular basis retest , no point will work in conjunction with the reference point for measurement, the standard of measurement stations and other allowable error overrun.

检查中发现了一些主要质量问题:一是部分变形观测与形变测量项目基准点埋设不稳固,变形监测点设置不符合规范要求;变形观测、计算未严格执行国家标准,如基准网未定期复测,未将工作基点与基准点进行联测,水准测量测站限差超限等。

If you like a person, in the allowable to tell him the truth.

如果喜欢一个人,在允许的情况下,告诉对方。

We don't have standards that say this is allowable.

我们没有标准,说这是允许的。

But in this instance it is allowable.

但是在这篇小说里还是允许的。

This is not allowable.

这不是允许的。

第13/500页 首页 < ... 9 10 11 12 13 14 15 16 17 ... > 尾页
相关中文对照歌词
Let's Humanize
Treasure It
It's What You Value
Open Letter (To A Landlord)
Tool
Yuh Whine Have Value
I Heart Throbsy
I Didn't Say I Was Powerful, I Said I Was A Wizard
3D
20th Century Blues
推荐网络例句

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他,我不喜欢他的这种性格。

As we know the price of traditional product is composed of the cost and the profit of the company involving market competition, monopolizes and many other factors.

我们知道作为传统的商品,定价的模式往往是在成本的基础上增加厂商的预计利润而形成其价格,当然也要考虑到市场竞争、垄断等其他方面的因素。