查询词典 allowable error

The adaptive program is calculated by T-B stress recovery scheme and z-z error estimation, the error is estimated by energy norm of difference of recovery stress and meshless stress. If the local relative error exceeds the limit relative error, then new nodes will be generated at the high error area.

本研究的自适应方法采用TB应力平滑技术和Z-Z误差估计，利用平滑应力和无网格法所得应力解差值的能量范数来估算误差，如果局部相对误差超过了允许误差，则在高误差域插入新的离散点进行加密。

Besides, we have studied deeply error of two kinds which appeared frequently in the hypothesis testing (error of the first kind and error of the second kind), including the relations to error of two kinds and its effect to the result of hypothesis testing and the effective control of error of two kinds so as to be satisfying and etc.

另外，对假设检验中经常出现的两类错误（第一类错误和第二类错误）也作了深入的探讨，其中涉及到了两类错误之间的关系，两类错误对假设检验结果的影响以及如何有效的控制两类错误使之达到令人满意的程度等。

In this paper the effects of scanning truncation error, scanning position error, random amplitude and phase error, and multiple-reflection error in near-field antenna measurement are analyzed; error equations and the uncertainty of measurement are obtained through computer simulation; compensated techniques for reducing the effects of measurement errors in near-field antenna measurement are presented and the formula and arithmetic of phaseless near-field techniques are derived.

本文从解析法和数值仿真两个角度深入分析口面天线近场测量中扫描面截断误差、扫描面位置误差、随机幅相误差、多次反射误差等误差源对天线远场特性测量精度的影响，一方面从理论上给出相应的误差方程，另一方面建立误差分析模型，通过计算机模拟，得到不同误差条件下测量结果的不确定度，并介绍了减小这些误差的修正方法，推导无相位近场测量的公式和算法。

The computation implies that the influence of truncation error of up/downwards continuation is about 0.001 m2·s-2, the maximum error is only 0.11 m2·s-2, which can be ignored in CHAMP gravity field recovery. The influence of the reference gravity field error of up/downwards continuation is less than 0.1 m2·s-2 in general, but the maximum error can reach 1.3 m2·s-2. To reduce this error, a high-precision gravity field model should be used in the up/downwards continuation.

计算表明：延拓误差中的截断误差部分影响量级约0.001 m2·s-2，最大误差仅为0.11 m2·s-2，可完全忽略；延拓误差中的参考重力场模型误差影响随参考场选取的不同而有所差异，整体而言小于0.1 m2·s-2，但最大误差可达1.3 m2·s-2，采用高精度的参考重力场模型能大大减小延拓误差影响。

The new method is given to design the optimum profile modification curve design The effects of optimum profile gear in improving the dynamic performance of gear transmission are verified in the Gear Dynamic Performance Test Rig In this dissertation, the main study contents and creative results are shown as following: The influences on the gear transmission system caused by the gear's accumulated error (periodic error and harmonic error) are theoretically studied. A new method is developed to simulate the gear's harmonic error by using the 2-order MARKOV process A simulated model of the dynamic performance which is excited by the gear's accumulated error is obtained.

本文在前人大量研究的基础上，结合作者承担的国家自然科学基金项目"齿轮传动动态系统辨识与三维修形研究"和山东省自然科学基金项目"齿轮传动动态性能仿真及结构参数、齿形的优化修形"，采用理论和试验相结合的新思路，系统地研究了齿轮传动的动态性能，建立了能正确描述齿轮传动系统动态性能的仿真模型和系统辨识模型，给出了确定齿轮传动轮齿修形曲线的优化设计方法，利用自行研制的齿轮传动动态性能试验装置，验证了优化修形齿轮对提高齿轮传动动态性能的突出作用。

A measuring system which mainly consists of a high precision motorized translation stage of one dimension, POINT GREY Flea2-14S3 CCD camera and LED light source was designed and constructed. Based on a detailed analysis for experiment results, the periodic changing law of system error of LED facula centroid location in this measuring system was found. The results indicate that based on Flea2-l4S3 CCD camera, the random error of facula centroid location is about 0.018 pixels, the system error is about 0.06 pixels, and the total error is about 0.063 pixels (1/15 pixels). According to the total error above, this CCD imager can be widely used in many measuring systems which count on facula centroid subpixel detection.

利用高精度一维电动平移台、POINT GREY Flea2-14S3 CCD相机和LED光源构建了测试系统，对测试结果进行研究和讨论，发现了测试系统LED光斑质心定位系统误差的周期性变化规律，计算得到了基于Flea2-14S3 CCD相机的光斑质心定位随机误差为0.018pixels，系统误差为0.06pixels，总体误差为0.063pixels（约1/15pixels），能够应用于以光斑质心检测为手段的测量系统中。

It is pointed out that the error of indication E0 for the calibrated test length which are measured when the offset length between the ram axis and the stylus tip is zero shall neither exceed the maximum permissible error MPEE0 nor exceed 1/3 of the probe error,that the repeatability of E0 shall neither exceed the maximum permissible error MPE Rnor exceed the repeatability error of the probe,and that if the measuring data is rejected in acceptance and reverification,measurement must be carried at least 5 times at the same position for reducing the possibility of misjudgement.

提出探测轴探针针头零偏置长度的校准测试长度的示值误差E0应不超过最大允许校准测试长度的示值误差MPEE0，且不应超过测头误差的1/3；E0的重复性误差R不应超过最大允许重复性误差MPER，且不应超过测头的重复性误差。建议验收校准测量数据超差剔除后，必须在相应位置重复测量5次以上，以减小误判的可能性。

Check method of residual error was used to judge data error, as if sum of front K residual error was unlikeness with sum of back n-K residual error in measure row, it shown that exist linear system error in measure row.

使用残余误差校核法，若测量列中前K个残余误差之和与后个残余误差之和不相等，则测量列存在线性系统误差。

The measurement accuracy of the photoelectric theodolite is decided based on measurement requirement of the ballistic trajectory. Two simple equations were derived mathematically, one expression for positioning error of the ballistic trajectory, angle error of the photoelectric theodolite, ranging error, target slant range and height when one instrument is used, another expression for positioning error of the ballistic trajectory, angel error of the photoelectric theodolite, target slant range and intersection angle when two symmetrical intersection instruments are used.

通过数学解析的方法，推导建立了2个简洁的公式：1）单站定位体制下弹道点位精度和光电经纬仪测角、测距精度以及目标斜距、高角之间的数学表达式；2）对称交会测量体制下弹道点位精度和光电经纬仪测角精度以及目标斜距、交会角之间的数学表达式。

In order to decrease the error rate of speech recognition, speaker adaptation techniques are often used to adjust speaker-dependent acoustic models. MLLR (Maximum Likelihood Linear Regression) and MAP are two of the most popular techniques in recent years. MLLR uses the technique of regression trees. It calculates the transform matrix for each leaf node of the tree. This makes it possible to use fewer sentences to decrease the error rate of HMM-based speech recognition. However, while we examined the recognition result, we found that although the overall error rate decreased, but the error rate of certain confusable phones was higher. In order to solve this problem, we propose the use MPE (Minimum Phone Error Discriminative Training) to solve this problem.

在语音辨识技术的实际应用上，语者调适技术常被用做调整语者无关之声学模型，使其对於特定语者之辨识率有所提升，常见的语者调适技术有最大化相似度线性回归（Maximum Likelihood Linear Regression），其精神在於透过对语音辨识模型相近的mixture做群聚，再对各个群聚做调整，以期能达到利用少量语料，提升辨识率的目的，但其缺点为，在发音上相近的模型，其mixture原本就极为近似，若再分类为同一群聚做调整，容易因为使用者的发音习惯，而使模型偏向ㄓ或ㄗ，因此虽然整体的辨识率获得提升，但却造成混淆音的错误率上升。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。