查询词典 allowable error

Although our script cur- rently supports only one type of error, we still use a generic error variable in case we wanted to continue development of thisscript to add more error detection in the future.

尽管我们的脚本目前只支持一种类型的错误，但我们仍然使用了一个通用的error变量，这是为了以后还可以继续开发这个脚本，给它增加更多的错误检测。

Position transformation error is a important part in research of north seeking scheme, the thesis analyses position transformation bringing error of north seeking in two-position scheme and brings forward the method of position transformation error measurement and compensation.

在寻北方案的研究中，转位误差是一个不可忽视的部分，文中以二位置为例分析了转位误差引起的寻北误差和转位误差的关系，并提出了测量和补偿方法。

Experiments were carried out to verify the static model. Experimental results show that the experimental curve matched well with the simulated curve, and there was certain error between them (maximal static error is 0.035 rad). The error cause was analyzed. Then the experiments were carried out to measure the dynamic performances of the side-sway joint. Experimental results show that the step response time of the joint was about 2 s steady value's tolerance zone ?

完成了侧摆关节静态特性试验，试验结果与仿真曲线基本吻合，验证了静态模型的正确性，但存在一定误差（最大静态误差为0.035 rad），分析了误差原因；对侧摆关节进行了动态特性试验，试验结果表明对于不同的期望值角度阶跃信号，侧摆关节开环阶跃响应时间大约是2 s

The complexity of bodywork decides variety of it's error. The station and primary factor which cause error is inconstant change and using correlation analysis can find out the primary factor. With an project given, the theory of correlation analysis for dimension variation of bodywork is discussed through correlation analysis and the layer structure of the bodywork,the state in which the error happened can be found out. How to use eigenva...

车体装焊的复杂性决定了误差产生的多因素性，车体制造过程中产生误差的工位和主要因素是不断变化的，采用相关性分析方法从众多的误差根源中准确地发现最主要的误差源；结合工程实践，论述了车体尺寸波动的相关性分析方法的原理，根据测量点的相关性分析和车体焊接工艺的层次结构，可准确地找到产生车体尺寸误差的工位；讨论了如何利用相关系数矩阵的特征值和相应的特征向量判断尺寸波动的模式，指出测量数据的波动主要按最大特征值所对应的特征向量方式波动，引起这种波动的原因是车体误差产生的主要原因，应重点采取措施加以控制；提出了应用计算机进行相关性分析的解决方案。

Firstly, we test that the error data are not normal distribution, and even the expectation is not zero. Then we analyze the possible type distribution of these error data. Finally, we use the stepwise method to fit the error data and obtain a function for some parameters of the SAIL model. As prior knowledge, the fitting function will be used to inverse these parameters ofthe SAIL model soon.

首先检验了误差数据不服从正态分布，甚至均值不为零；然后对误差数据可能服从的分布类型给予了解析，得到了指数分布和混合正态分布两种不同类型的可能分布；最后拟合了误差关于SAIL模型部分参数的函数表达式，以作为先验知识应用于反演之中。

Comparison of the synchronous measurement result of this receiver with that of a reference one shows the error trend is the same. The scatter plots of the horizontal error and vertical error distribution show that this measurement system is more stable and can reflect the position information exactly.

该接收机和参考接收机的同步测量结果表明，两个接收机对定位信息获取的误差趋势相同，通过接收机的水平误差散点图和时间序列垂直误差分布图可见，该测量系统较稳定，可准确地反映定位点的位置信息。

Simulation results show that in the image rotation and scale variation range resulted from the navigation system error and the measurement error of the wireless pressure altimeter, the proposed image matching algorithm can satisfy the accuracy demands of the scene aided navigation system and provide the location error-correcting information of the system.

仿真分析表明，在导航系统误差漂移所引起的图像旋转和气压高度表所引起的尺度变化范围内，该算法能满足匹配准确性的要求，并能有效给出系统的定位误差修正信息。

In the second chapter,I calculate the diffractive efficiency when there arealignment error,depth error of the step and the work was elength error,based on the theory ofthe fresnel lens.

第二部分文章在介绍菲涅耳透镜设计原理和衍射效率计算的基础上，重点分析了存在各种加工误差时候的衍射效率的计算情况。

Having a lower wattage in comparison with the above-described models, this PSU has a higher allowable load on the +12V rail.

具有低功率相比，上述型号这psu具有较高的允许负荷的升五轨。

You may also want to check your grammar to see if it allows words that are acoustically similar (for example,"repeat/delete,""Austin/Boston," and "Addison/Madison"), and determine if there is any way you can make the allowable words more distinctive to the engine.

你可能也想看看你的语法，看看它是否允许的话，从声学角度类似的(例如，"重复/删除"、"奥斯汀/波士顿，"和"艾迪/麦迪逊")，并决定是否有任何方法可以让你的允许的话，更与众不同的引擎。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。