查询词典 allowable error

To improve the pointing accuracy of the telescope mount and the capability of daylight tracking, it is necessary to do more study on the error of telescope axes. The present thesis analyses many kinds of factors that cause the pointing error of telescope mount, and discusses the method for correcting the pointing error by setting up telescope mount model in detail.

本文详细分析了望远镜机架指向产生偏差的各种因素，讨论了通过建立望远镜机架指向误差模型的方法来修正望远镜机架指向误差的方法，通过使用CCD观测恒星来求解望远镜机架指向误差模型参数。

Fist, comprehensive analysis on the current study on data processing is made, and characters of Newton methods about nonlinear surveying and mapping data processing are discussed, and then new solutions to parameters estimate with multi-sources, multi-types, multi-dimension, multi-precision bynonlinear least square are presented such as PSB algorithm, digital continuation and generalized digital continuation algorithm, cone model method, tensor analysis method, GCMA(mixed algorithm of gradient method and conjugate gradient method), combining algorithm based on Newton method and gradient method and confidence region and so on, and a new fast difference iterative algorithm is proposed towards parameters estimation containing random parameters in nonlinear models, and a new solutions to nonlinear least squares surveying and mapping adjustment by parameters estimation both considering the random and nonrandom parameters is presented after studying on nonlinear data processing in deformation monitoring, and at last primary analysis on error propagation of spatial data is made and approximate error propagation formula and error analysis formula to length and area are proposed.

首先比较全面分析了目前测量数据处理理论的研究现状，讨论了牛顿类方法在处理非线性模型参数估计方面的特点，研究并给出了求解多源、多类型、多维、多精度、非线性最小二乘测量平差参数估计的若干种新方法，这包括PSB算法、数值延拓及其广义数值延拓算法、锥模型法、张量分析法、基于最速下降法和牛顿法的组合算法、基于最速下降

In the regular wave experiment, the transverse error of wave height is less than 2%, the repeated error of the wave height is less than 1.28%and the period repeated error is less than 0.2%.

介绍了实验室的造波机系统和造波特性及其在模型试验中的应用，并讨论了实验室内模拟海浪的检验标准及其方法。

This paper analysed generating mechanism of the dynamic error induced by the model truncation error and presented a method of varying shift matrix to reduce the effect of the model truncation error on system performance.

文中分析了产生动态偏差的机理，提出了一种根据截断误差大小选取不同位移矩阵来校正截断误差的方法，减小了截断误差对系统性能的影响。

As a result of error distribution\\\'s non-uniqueness, draws out to the standard deviation understanding again, by about standard deviation reflected that the erroneous zero rank value two side the variation targets, the application unimodal distribution fits the error distribution, the goal is: By approaches the rationality which under the enhancement goodness of fit\\\'s premise determines to the error.

从文章的上下文感觉此标准值似乎是人为规定的，并不受实测数据本身分布的影响，不具有客观性。个人认为：研究在实际中实测数据相对于均值的分布更有意义。按照作者的观点，误差的分布都是单峰的，除了正态分布这种对称分布外，作者认为还有不对称的偏峰分布。因此研究这种偏峰分布模型可能更有意义。

The sources of leading error were analyzed,the error generating process was described,and the vector equation of the leading error was built up.

主要分析了战斗机引导误差来源，对引导误差的产生过程进行了矢量描述，推导出引导误差矢量方程。

Aiming at T-base diamond lathe, author use both on-line and off-line to measure the error vector of lathe workspace, and acquire good network train samples, then build two-dimensional error compensation model of lathe workspace with BP neural network and fuzzy neural network, at last build contour error compensation control system.

在分析国内外数控机床伺服闭环系统的发展现状及局限性的基础上，利用原数控系统和所研制的二维压电陶瓷微动刀架，研制了独立于原数控系统的超精密闭环控制系统。

The error includes two sides, one is the calculation error about Wheatstone bridge circuit, and another is the effect of the sharp pulse producing when test current is loaded on the sample. In order to eliminate or decrease error, some measures are employed in the test program.

2进行了无损性验证试验，结果说明经过瞬态脉冲试验的产品的感度性能与未经过瞬态脉冲试验的产品的感度性能相比，没有显著性差异。

Aiming at researching on the theory of the shaft-kind parts form error evaluation and its application, on the basis of the analysis for the geometric model of the roundness error and cylindricity error, the linear programming models of the enclosure evaluation were proposed. According to the features of the proposed models, the solution of the optimization algorithms of linear planning was discussed to obtain accurate evaluation results.

为了对轴类零件形状误差评定理论及应用进行研究，在分析轴类零件的圆度、圆柱度误差评定几何模型的基础上，建立了包容拟合评定的规划数学模型，并针对模型的特点，探讨了使用线形规划的单纯形优化算法进行规划模型的求解，从而获得精确的形状误差评定结果。

Four methods for evaluating circularity error. least-squares method for evaluating cylindricity error. 3.Using language of VC++, a software of form error evaluating is developed. Module structure is adopt in this software and every element has one module.

用VC++开发了形状误差的评定软件，软件采用功能模块结构，每种元素均设计为一个独立的模块，为使评定结果更加直观，采用OpenGL对处理的结果进行了可视化处理，结果图形可以随意转动和缩放，以方便观察。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。