查询词典 aldehyde resin

Our company has six sets of polyketone resin production equipment, three sets of aldehyde resin production equipment and five sets of UV oligomers production equipment, with annual capacity of 2,500-ton polyketone, 1,000-ton aldehyde resin, and 4,000-ton UV oligomers, and is one of the largest manufacturers of aldehyde resin , polyketone resin and UV oligomers in Asia.

有六套聚酮树脂、三套醛树脂、五套UV光固化树脂生产装置，年产聚酮2，500吨，醛树脂1，000吨，UV光固化树脂4，000吨，是亚洲最大的醛树脂、聚酮树脂、UV光固化树脂生产企业之一。

The effects of solution\'s pH value, mol ratio between phenyl aldehyde and L-Arginine, concentrations of sodium chloride, ammonia chloride andL-Lystine, initial concentration of L-Arginine on precipitation rate of a -tolylene arginine were investigated, the results indicated that phenyl aldehyde precipitation method\'s appropriate pH value was higher than 11, suitable mol ratio between phenyl aldehyde and L-Arginine was 1.25, initial concentration of L-Arginine was must higher than 15g/L, sodium chloride had little effect on precipitation rate, on the contrary, ammonia chloride and L-Lystine had great effect on it, both of them must be eliminated; At the same time, adsorption isotherm at 25 C of L-Lystine on anion exchange resin A was measured, the result showed that the maximal equilibrium adsorbance was 30mg/g, the influences of solution\'s pH value, temperature, concentration of chloride ion on adsorption of L-Lystine by anion exchange resin A were also studied, the results indicated that appropriate operational pH value was 0.5 0.2, the effect of temperature on adsorption ratio was little, process could be operated at room temperature, the concentration of chloride ion must be eliminated.

考察了溶液pH值、苯甲醛与L-精氨酸摩尔比、氯化钠与氯化铵浓度、L-赖氨酸浓度、L-精氨酸初始浓度对苯甲醛沉淀L-精氨酸的影响，结果表明，沉淀反应的适宜pH值大于11，苯甲醛与L-精氨酸的适宜摩尔比为1.25，(来源：Aa6BC论文网www.abclunwen.com)L-精氨酸适宜的初始浓度在15g/L以上，氯化钠的存在对沉淀率基本上没有影响，而氯化铵和L-赖氨酸的存在使沉淀率下降；同时测定了25℃时阴离子交换树脂A吸附L-赖氨酸的吸附等温线，表明其最大平衡吸附量为30mg/g，考察了溶液pH值、温度、氯离子浓度对阴离子交换树脂A吸附脱除L-赖氨酸的影响，结果显示从L-精氨酸和L-赖氨酸混合液中吸附分离出L-赖氨酸的适宜pH值为10.5±0.2，温度对L-赖氨酸吸附率影响不大，吸附过程可在室温下进行，氯离子的存在使L-赖氨酸的吸附率降低。

Resins: gum dammar; PU dispersion; silicone resin, epoxy resin, alkyd, acrylic Resin, polyester resin, urethane resin, polyamide resin, amino hardener; two pack hydroxy acrylic, two pack isocyanate-free acrylic; vinyl chloride co-polymers, polyvinyl butyrals, thixotropic resin.

树脂类：达玛树脂；水性PU分散体；有机硅、环氧、醇酸、丙烯酸、聚酯、聚氨酯、聚酰胺、氨基固化剂；双组份羟基丙烯酸、双组份不含异氰酸脂丙烯酸；聚氯乙烯共聚物、聚乙烯醇缩丁醛、触变性树脂。

The method includes the steps of forming a peelable resin layer on a silicon substrate, forming the wiring substrate on the peelable resin layer, mounting semiconductor chips on the wiring substrate, forming semiconductor devices by sealing the plurality of semiconductor chips by a sealing resin, individualizing the semiconductor devices by dicing the semiconductor devices from the sealing resin side but leaving the silicon substrate, peeling each of the individualized semiconductor devices from the silicon substrate between the silicon substrate and the peelable resin layer, and exposing terminals on the wiring substrate by forming openings through the peelable resin layer or by removing the peelable resin layer.

该方法包括以下步骤：在硅衬底上形成可剥离树脂层；在所述可剥离树脂层上形成布线衬底；将半导体芯片安装在所述布线衬底上；通过用密封树脂密封所述多个半导体芯片来形成半导体器件；通过从密封树脂侧将这些半导体器件切分但是保留硅衬底来使这些半导体器件个体化；将每个个体化半导体器件在所述硅衬底和可剥离树脂层之间从硅衬底上剥离；并且通过形成穿过可剥离树脂层的孔或者通过除去可剥离树脂层来使布线衬底上的端子暴露。

Shanghai exchange resin resin plant special enterprises in China are domestic professional research and development, application, management services, OEM resin enterprise as a whole.major enterprises in China have Styrene, acrylic acid series, strong acid, strong base, weak acid, weak base, chelating , inert ion exchange resins, special enterprises in China for many years with several well-known enterprises to explore the application of ion exchange resins, the key products used in softened water, desalination water treatment-exchange resins; condensate treatment resin; food, fermentation industry Decoloration, dedicated Absorption resin, petroleum, chemical, medical, chelate resin and catalyst series dedicated resin as well as ancillary treatment, such as a series of packing products, such as a variety of grades.

上海汇脂树脂厂特华企业是国内专业研究开发、应用、管理服务、OEM为一体树脂企业。特华企业主要有苯乙烯系、丙烯酸系列，强酸、强碱、弱酸、弱碱、螯合、惰性离子交换树脂，特华企业多年来与多家著名企业探讨离子交换树脂应用，目前主要产品应用于软化水、除盐水处理交换树脂；凝结水精处理树脂；食品、发酵行业脱色、吸附专用树脂、石油、化工、医学、鳌合系列树脂和催化剂专用树脂以及配套水处理的系列填料等多种牌号等系列产品。

Was established in 2002, Foshan City, formerly known as Qing Cheng Chemical Co., Ltd., is a company specializing in the provision of paint, ink resins and the main raw materials such as paint additives companies, products include: Solid thermoplastic acrylic resin , aldehyde and ketone resins, poly ketone resin, formaldehyde resin, chlorine vinegar resin, polyurethane resin, paste wax, solvents such as DBE.

广州优霓科贸易发展有限公司于2002年成立，前身是佛山市清诚化工有限公司，是一家专业提供涂料、油墨主体树脂及颜料助剂等原辅料的公司，产品有：热塑性固体丙烯酸树脂，醛酮树脂，聚酮树脂，醛树脂，氯醋树脂，聚氨脂树脂，蜡浆，溶剂DBE等。

PLASTICS AND RESIN: AB、ABS emulsion, uric acid resin, phenolic aldehyde resin, urea-formaldehyde resin, formaldehyde resin, polythene,poly-chloroprene and etc.

塑料树脂： AB，ABS乳液、尿醛树脂、酚醛树脂、密胶甲醛树脂、聚乙烯、聚氯乙烯等。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cylinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature. Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable.

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

Plastic should lower 3 steps, because plastic is a step to add melt resin material to cyclinder , Higher stick of resin material ,higher screw back pressure. Screw speed differs depending on decomposing temperature of resin material ,Higher screw speed ,Higher trim force of resin, higher cyclinder temperature.Some resin material may decomposes so it set screw speed in mid-speed such as 45-75%, In plastic step setting screw back pressure is very important, Higher screw back pressure ,higher quality of product screw back pressure make resin structure order, Molding product is beautiful and volume stable. But

再复杂的熔胶旋转过程最多不会超过三段，因为熔胶本身就是存在于把胶熔进料筒的过程，如果原料粘度大，熔胶压力则大，但速度则应取决于原料的分解温度，熔胶速度越快，原料中的剪切力则会越大，料管温度则越高，局部原料产生分解的可能性则会越大，故一般熔胶会采用中速为宜，如45%-75%，熔胶同时会碰到一个比较重要的环节，那就是背压的使用，产品精度要求越大，背压的使用则更大，背压可使原料分子间结构更紧密，成型出的产品则尺寸更稳定，外观越好。

You can buy sweetened beverages, if that suits you.

你若喜欢的话，可以买些含有糖精的混合饮料。

As many of you are probably aware, Nick and Vanessa were recently faced with an embarrasing sex scandal after naked pictures of the two getting jiggy with it in a hot tub surfaced the net.

正如很多你可能知道，尼克和 Vanessa 最近面临一个尴尬的绯闻事件后，赤裸裸的图片两个越来越jiggy与它在浴缸中的一个热点浮现净。