查询词典 air temperature

The NOx concentration of the outlet of the combustion chamber increases with the temperature of preheated air.

得出燃烧室出口NO_X的浓度随预热空气温度的增加而增加。

Wet bulb temperature ; enthalpy ; saturated air ; atmospheric pressure ; psychrometric chart

湿球温度；焓；湿饱和空气；大气压；焓湿图

Pyrology ; Radiant floor cooling ; Dedicated outdoor air system ; Dew point ; Surface temperature

热工学；地板辐射供冷；独立新风系统；露点；表面温度

Methanol can pyrolyze and generate hydrogen when it is heated by the exhaust of diesel engine(temperature range between 400℃and 600℃). Then let the hydrogen generated from methanol go into cylinder with the air directly. By this means, we hopefully increase the rate of economizing oil of emulsified fuel in diesel engine.

利用柴油机排烟(温度一般在400～600℃)余热加热甲醇热分解制氢，并在线通入到柴油机进气道入口，有望实现柴油机燃用乳化油时节油率的提高。

The effect of some key factor such as reburn zone temperature,stoichiometric coefficient and reburn rate on NOx formation regulation was studied on a one-dimensional test system with multi-function such as air stage and fuel reburning.

燃料型NOx是主体，约占75%～80%，燃料型NOx又可以分为挥发分NOx和焦炭NOx，在这两部分中挥发分NOx是主要部分，它在燃烧初始阶段形成。

The experimental results showed, after absorption of CO2, the material could be reprepared, whose performance of absorbing CO2 for the second time is affected by the temperature and air flux during repreparation.

实验结果表明，在吸收CO2后材料的再次合成过程中合成温度及空气流量影响材料吸收CO2的循环性能，在再次合成温度为750℃，空气流量为100mL／min的条件下，合成的材料具有良好的循环吸收CO2的性能。

Long time, because the main city of Chengdu is located in the hinterland of Sichuan Basin, the seasonal high frequency of calm winds, temperature inversion strength, subject to a special geographical environment and climatic conditions, in a natural state, city over to respirable particulate matter, sulfur dioxide, represented by the proliferation of difficulties in dilution of air pollutants, resulting in a large number of pollutants in the basin, retention, accumulation.

长的时间，因为成都的主要城市是位于四川盆地，平静的季节风高频率的腹地，逆温强度，受特殊的地理环境和气候条件在自然状态，城市对可吸入颗粒物，二氧化硫，由空气污染物的稀释扩散代表的困难，在污染物在盆地，保存，造成大量积累。

By setting the retting duration of 20 hours, the factors affecting the residual gum percentage of the retted kenaf fibers are studied. The experimental results show clearly that the following factors have the significant influence on the residual gum percentage of the retted kenaf fibers and show the obvious variation tendency. The preferred processing parameters are as follows: pH value 7. 0、bath ratio 1: 50、reuse percentage of retting liquid 50%、air flow volume 2. 5L/min、temperature 40℃、nitric additives (ammonia is better than nitrates) percentage 0.45%.By comparison with anaerobic retting, the retting duration using aerobes is much shorter than that using anaerobes.

确定了以好氧微生物脱胶作为本课题的脱胶路线后，在特定的脱胶时间（20小时）条件下，通过分析不同参数条件下的残胶率，研究了好氧微生物脱胶的各种影响因素对红麻脱胶的影响规律，并优选出最佳脱胶液回用比为50％，最佳pH值为7.0，最佳气流量为2.5L/min，最佳浴比为1：50，最佳水浴温度为40℃，最佳含氮添加剂为铵盐类化合物，最佳含氮添加剂用量为0.45％。

It has the characteristics of stainless steel material, use the electronics to adjust time, control temperature and expel the air automatically, it is used to fry chicken, fish, sparerib, mutton, and all kinds of meat and vegetable.

整体不锈钢为主要材料、电子定时、控温自动控压排气。采用低温高压原理，炸制的食品外酥里嫩，色泽鲜明，还可以炸鸭、鱼、排骨、羊肉等各种肉类和蔬菜、土豆。

By the simulation computation, the present work obtained the spectroradiometric function with temperature, wavelength and the air transmittance as the parameters, and got the characteristic of data from difference background radiation. The spectrum D-value function shows the energy of the spectrum in different situation.

采用AViiVA-M2型CCD相机、静态傅里叶干涉具、 1 m×1 m的铁板作为待测目标等做相关实验，分别在一天中不同时间、不同探测距离、不同背景的条件下，得到了各种情况下整个系统的探测极限位置。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。