查询词典 affine parameter

Based on the method used to calculate ground elastic displacement around deep tunnel and some researches on gap parameter of shield tunnel, a brief method for estimating subsurface ground horizontal movement induced by shield tunneling is presented.

在深埋隧道周围土体弹性位移计算方法及盾构问隙参数研究成果的基础上，通过相应的分析和假设提出了一种预测盾构隧道施工引起地表下土体水平变位的简便估算方法。

In order to improve the condition of guide device of 3 500 mm finish mill and reduce the failure rate,a series measures were adopted: ameliorating hanging position of the guard plate,optimizing occlusal surface parameter of the uide wien guard tlate,altering guard plate location mode when changing roll,redesigning the bottom of guard sheet.

为改善3 500 mm精轧机导卫装置设备状况，减少故障，改进了护板吊挂方式，优化了导板与护板咬合面参数，改变了换辊时护板定位方式，重新设计了护板底部形状，消除了安全隐患，满足了高质量快节奏生产的要求。

The static and dynamic characteristics of the beam of a gantry-type machining center are analyzed by means of ADAMS and ANSYS. Considering effect of gravity and cutting forces, the static deformation of the beam is obtained after calculating the interacting forces between the guide and the slide block by ADAMS. Moreover, the contact parameters of the guide surface are acquired by dynamic tests and parameter identification, then they are applied to the simulation model of the beam-slide box system, whose natural frequencies and modal shapes are achieved by modal analysis. Furthermore, the effect of changes of the contact parameters on the dynamic behavior of the beam-slide box system is also investigated.

对一种国产龙门式加工中心的横梁关键部件，采用机械系统多刚体动力学仿真软件ADAMS和有限元分析软件ANSYS进行了静动态特性分析；在考虑重力和切削力作用下，由ADAMS计算出导轨与滑块间的作用力，从而计算出横梁部件的静态变形；通过动态测试和参数辨识方法获得导轨结合面特性参数并将其应用到横梁滑箱系统整体有限元模型中，经过模态分析得到系统固有频率和各阶振型图，并进一步分析了结合面参数变化对横梁滑箱系统整体动态特性的影响。

That is why peacetime production management, we often business card printing and membership card making ink parallel the parameter value to detect operators on the machine's maitanence, typically requires that operators, mainly from the following six: on the day of completion of cyclophos phamide-Indian newspapers, to set the machines all the water gum, ink, adhesive for very good cleaning.

所以平时的生产管理中，我们经常通过制卡和会员卡制作过程中水墨平行各参数值来检测操作人员对机器的维护和保养情况，通常要求操作人员主要从以下六个方面着手：①印完当日报纸后，要将机器所有的水胶、墨胶进行很好的清洗。

Moldflow software was used for searching for optimal parameter of forming process of ABS gusset plate by simulating real condition. Some main factors which influenced the process of injection molding were found out after the simulation analysis of filling and flowing.

通过模拟真实注射条件，应用Moldflow软件对ABS扣板注射成型工艺参数进行了优化分析，得出影响注射成型顺利进行的主要因素，并模拟制定出扣板注射成型的最佳注塑压力、锁模力、模具温度、熔体温度、注塑时间、保压压力、保压时间和冷却时间。

To reduce and compensate the influence of temperature on ring laser gyro bias error and attain the precision of inertial level gyro, the mechanism of RLG zero-bias error due to temperature is analyzed. Based on a great number of environmental temperature experiments of RLG, a general temperature compensating model and a new kind of BP neural network model are established. A method for identifying the model parameter is proposed. Simulation results show that the simplified compensating model can reduce the zero-bias by more than a magnitude and achieve real-time compensating feature.

零偏是衡量激光陀螺性能的一个重要指标，但其受温度影响很大，为了降低和补偿温度对激光陀螺零偏的影响，使其达到惯性级陀螺仪的精度要求，分析了温度对激光陀螺零偏误差的产生机理，在大量高低温环境试验的基础上，建立了一种通用的零偏温度补偿模型和一种BP神经网络模型，并给出了模型参数的辨识方法，仿真结果表明，对该模型作适当的简化，可以将零偏减小一个数量级以上，而且具有实时补偿性能。

Therefore, whenever one needs to determine an unknown hadronic parameter, the QCDsum rule prediction is a reliable one.

因此，当需确定未知的强子参量，QCD求和规则是个可以信赖的工具。

Add one column in continuously monitors table for process parameter, and print it and hand over to the quality department to audit and record.

在工艺参数连续监控记录表中增加一栏整改措施记录，并打印文本交品质部门进行监督存档。

It has the advantages of minitype,simple structure,passive sensing head, little spectral deformation, simultaneous multi-parameter measurement.

该系统具有小型化、结构简单、探头无源、所得光谱变形小、多参数同时测量等特点。

Based on the processed accessory, the number, the position and the machining data of the holes and the form of the principal axis are determined; The driving way of the headstocks are drawn, the power is transmits by the methods of optimization, the driving parameter are determined, the structure of the principal axis are designed and the strength of the parts, such as the gears and the bears, are checked.

根据被加工零件确定加工孔的数量、位置、切削用量及主轴类型，拟订了主轴箱的传动方式，应用最优化方法传递功率，削减振动，确定传动参数，设计轴的结构，进行如齿轮、轴承等相关零件的强度校核计算。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。