查询词典 adopts

Data acquirement adopts B/S model,Data application adopts C/S model.

汽车检测数据采集采用C/S模式，数据应用采用B/S模式。

The machine's control system adopts a delta DVP14SS11R and a module of DVP16SP11R (16 I/O expansion module).It Composes 40 PLC control section. It adopts a module of DVP02DA-S (2 group simulation quantity output module) to control main frequency conversion and fluctuation frequency conversion actuation. The machine also adopts a delta TP04-AS2 Text display monitor carrying on the system external input with to reel thread the data monitoring. Use plate alternating current machine driver VFD-B-P series frequency changer controlmasterdrive electrical machinery and ring board electrical machinery.

该机型整个控制系统采用了一套台达DVP14SS11R控制单元，配DVP16SP11R扩展模块（16点I/O扩展），来组成40点PLC控制部分，采用一块DVP02DA-S（2路模拟量输出模块）分别控制主变频和升降变频驱动，同时采用台达TP04-AS2文本显示屏进行系统外部输入与纺纱数据的监控，使用台达VFD-B-P系列变频器控制主传动电机和钢领板电机。

The machine's control system adopts a delta DVP14SS11R and a module of DVP16SP11R (16 I/O expansion module).It Composes 40 PLC control section. It adopts a module of DVP02DA-S (2 group simulation quantity output module) to control main frequency conversion and fluctuation frequency conversion actuation. The machine also adopts a delta TP04-AS2 Text display monitor carrying on the system external input with to reel thread the data monitoring. Use plate alternating current machine driver VFD-B-P series frequency changer control master drive electrical machinery and ring board electrical machinery.

该机型整个控制系统采用了一套台达DVP14SS11R控制单元，配DVP16SP11R扩展模块(16点I/O扩展)，来组成40点PLC控制部分，采用一块DVP02DA-S(2路模拟量输出模块)分别控制主变频和升降变频驱动，同时采用台达TP04-AS2文本显示屏进行系统外部输入与纺纱数据的监控，使用台达VFD-B-P系列变频器控制主传动电机和钢领板电机。

The main brake adopts energy-consumed braking; the auxiliary brake adopts the new-type band brake; the mechanical drive adopts a driving method which combines cycloidal reducer and chain drive; the bailing metering unit adopts the digital control mode which uses the single-chip microcontroller as the central processing unit.

该绞车采用交流变频控制，实现无级调速；主刹车采用电动机能耗制动，辅助刹车采用带棘爪机构的带式刹车；机械传动采用摆线减速器与链传动相结合的传动方式；捞砂计量装置采用单片机微控器作为中央处理单元的数字控制模式。

Thereinto,the measuring circuit is composed of heating circuit, voltage follower circuit, warning circuit, gas sensor failure indication circuit and power supply indication circuit;The microprocessor adopts 8051 Single - Chip computer;The LED adopts Seven LED figures display;The keyboard adopts separate type non-coding keyboard.

其中测量电路由加热电路、电压输出电路、报警电路、气敏元件损坏指示电路和电源指示电路组成；微处理器采用8051单片机；LED显示采用七段LED数码显示器；键盘采用的是独立式非编码键盘。

Br/br/Adopts the GHH-RAND remarkable mainfrane br/(150HP-300HP) screw air compressor rotor is the German GHH-RAND joint shaft type unit,adopts the third generation asymmetrical dentate 5:6 rotors,The major axis is more reasonable than the choice, the tangent speed of rotors is only 30-36m/s, is far lower than that60m/s of common air compressors, it keeps 0.003INCH between rotors that will not abrase forever, the space between teeth dropping variance is small, so the backflow loses is slight, Enhances10-12 kf the efficiency compared to the 4:6 dentate, save power 20, adopts the Swden SKF bearing.

采用GHH-RAND卓越主机br/（150HP-300HP）螺杆机转子为德国GHH-RAND联轴式机组，采用第三代非对称齿型为5：6的转子，长径比选择合理，其转子的切线速度仅为3036m/s，远低于一般空压机60m/s 的切线速度，转子之间保持0.003INCH间隙永不磨损，齿间落差小，故回流损失小，比4：6齿型提高效率10-12，省电20，采用瑞典SKF轴承，极大延长了主机的寿命。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts osci llating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thellomble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thellomble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文预设的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的毗连方式采用能蒙受较大载荷的无内圈双列滚针不锈钢管，且直接采用不锈钢管外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹毗连的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts oscillating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thimble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thimble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文设计的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的连接方式采用能承受较大载荷的无内圈双列滚针中国财经圈，中国财经圈，且直接采用进口中国财经圈外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹连接的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

JS11 Intelligent Straight-line Beveling Machine and a PG10 glass polishing machine, Its Joint-Link adopts chainless ball bearing construction .smooth transmission, high-precision movement , The controlling system adopts PLC, which can be operated manually or automatically. The human-machine interface displays various parameters, such as the glass thickness, bevel width and angel, remaining thickness, and working speed The convey speed adopts speed adjustment of frequency conversion The machine can grind and clean the rear transmitting plate of itself.

JS11玻璃直线斜边磨边机及PG10璃直线斜边抛光机采用无链条轴承滚动链板结构，传动平稳，运动精度高，控制系统采用PLC控制，可自动、手动转换，人机界面清楚显示玻璃厚度、斜边宽度及角度、剩余玻璃厚度和加工速度等各种参数，参数的输入和修改直观、便捷，自动化程度高，传送速度采用变频调速，能在本机上进行修磨后板，并设有后板自动清洗装置。

The low volt winding generally adopts cylinder type Structure winded by copper foil except some small capacity winding,which adopts copper conductor;the high volt winding adopts multi-layer cylinder type structure,which drives ampere-turn of winding more balanced laying and flux leakage smaller .

低压绕组除小容量采用铜导线以外，一般采用铜箔绕制的圆筒式结构；高压绕组采用多层圆筒式结构，使之绕组的安匝颁布平衡，漏磁小。

In the negative and interrogative forms, of course, this is identical to the non-emphatic forms.

。但是，在否定句或疑问句里，这种带有"do"的方法表达的效果却没有什么强调的意思。

Go down on one's knees;kneel down

屈膝跪下。。。下跪祈祷