查询词典 admissible deformation

Children infancy is the most rapid growth period, because of its skull soft and elastic texture, easy to deformation, if the parents pay no attention to your baby's sleep position, every day is always in one direction to sleep, time, deformation on the head will not free of.

婴儿期是小儿生长发育最迅速的时期，由于其颅骨质地柔软而富有弹性，容易变形，若家长不注意孩子的睡眠姿势，天天总是朝一个方向睡，时间久了，头部变形就不可必免了。

In addition, because the temperature in the head end and tail end is usually lower, the higher roll force leads to higher deformation for the roll and stand and consequently, a smaller roll gap is needed for the head end and tail end, in order to achieve equal deformation among the head end, tail end and body.

此外，由于温度在头端和尾端通常较低，较高的轧制力导致较高的轧辊和机架变形，因此，轧件头端和尾端需要较小的棍逢值以实现其头部，尾部和中部的均匀变形。

Preload condition, the cylinder head bolt-hole depth of deformation of the cylinder sets a great impact on the proper cylinder head bolt hole depth Shen cylinder liner to reduce the deformation.

预紧工况下，缸盖螺栓沉孔深度对气缸套变形影响很大，适当的缸盖螺栓沉孔深度有利于减小气缸套变形。

The analysis shows that, blade vibration and torsional deformation is the mainly manifestations of the cutting mechanism head body ,the maximum deformation of the helical blade is 18.01mm, the maximum stress value in the welding of corner ,connection of end disk and helical blade is the weak link, helical blade is the main component, which effects the dynamic characteristics of cutting mechanism head body.

所得结论对于改进螺旋钻采煤机截割机构头体的设计、提高其动态性能和使用寿命具有一定的指导意义和参考价值。2、文章中部分措词需要修改，摘要翻译中文化，论文整体格式需要修改。3、数值模拟的约束条件有待商榷，对于结果应该对比实际试验和有关材料特性表，更有说服力。

A correlation of the experimentaldynamic response of the vessels with the theoretical finite element calculations ispresented and discussed.1 The response of the end caps is dominated by transverseand torsional deformation of the plates.The membrane strain is negligible compareto the lateral strain.2 In the lengthwise direction of the inner cylinder,themembrane strain has the same magnitude as that of the bending strain. But for theouter cylinder,the former is much smaller than the later at the same direction.3 Forboth the inner shell and the outer shell,hoop strains are primarily due to themembrane deformation.The amplitude of the circumferential flexural strain isconsiderably small.4 Peak strains in the vicinity of the connection portion of theend caps and the shells are very high.This is important to assess the safety of thecontainer in case of repeated use or tests.5 The applying load to the end cap isdifferent from that to the inner shell plate, but peak stains and nodal displacementsof these two structural parts are nearly the same.It can be inferred that the dynamicresponse of the end cap is greatly affected by the structural vibration excited by theimpulsive loading.

结果表明：1在本文所考虑的载荷水平下，平板变形以板的横向弯曲和扭曲为主，中面应变幅值比较小。2对于内容器，其纵向变形中弯曲应变和中面应变大小接近；而对于外容器，其纵向变形以弯曲为主，中面变形比较小。3内、外壳体的环向变形主要是中面应变，弯曲应变分量很小。4平板和壳体连接处应变很大，这对于多次使用或实验时评价结构安全有指导意义。5尽管内筒底板和大封头上的作用载荷有一定差别，但应变峰值和节点位移峰值基本相近，这说明脉冲载荷激发起来的结构振动对封头的动态响应有很大影响。

The activation energy for deformation in W18Cr4V high speed steel, 40CrMnNiMo tool steel for plastic molding and AISI H13 hot-work tool steel are investigated intensively. The investigation shows that the activation energy for deformation of both 40CrMnNiMo tool steel for plastic molding and AISI H13 hot-work tool steel decrease with the increasing of temperature.

分别将这两种钢的变形激活能数学模型用于蠕变模型，并采用这一改进后的蠕变模型对W18Cr4V高速钢和40CrMnNiMo塑模钢的热变形流变应力进行预测，结果表明，此模型不仅能精确描述蠕变条件下工模钢的流变应力变化规律，也能精确描述工模钢非蠕变条件下的流变应力。

Secondly, a theoretical dual rigid-plastic modal under lateral impact of blunt indenters is firstly developed in order to predict damage pipeline which is fully clamped across a span based on rigid-plastic beam on a perfectly plastic foundation, which is made up of a rigid-plastic sub-beam and a rigid-plastic basic-beam, the rigid-plastic sub-beam is used to predict denting deformation, the rigid-plastic basic-beam is used to predict global deformation, the sub-beam and the basic-beam interact by a perfectly plastic foundation.

为了更好地估计钝头弹体冲击对管道造成损伤，在刚塑性地基梁模型的基础上，首先提出了一种新的理论计算模型一双重刚塑性梁模型，由一子梁和一基梁构成，子梁用来估计弹体撞击造成的局部损伤，基梁用来估计弹体撞击造成的整体弯曲，子梁和基梁通过基础反力相互作用。

Depending on the relation between winding deformation and leak inductance ,it is pointed that the exact and real-time calculation of leak inductance is the key factor of winding deformation monitoring,especially of the technique development from off-li.

结合变压器绕组变形与漏电感参数的变化关系，指出变压器绕组漏电感参数的准确实时计算将成为绕组变形监测，尤其是从离线到在线监测技术发展的关键问题。

On the analysis of the status of rendering surface deformation isograms, and based on the new features of Microsofts latest software development tool－Visual Basic 2008（VB2008）, solutions were proposed, that to develop program for rendering surface deformation isograms in mining areas.

分析了开采沉陷预计矿区地表变形等值线绘制的研究现状和微软最新软件开发工具VB2008（Visual Basic 2008）的新特性，提出基于VB2008开发地表变形等值线绘制程序的方法。

A large number of twins was found in bainitic midribs for first time. Twins in midribs as well as retained austenite are deformation twins formed by coordinating uniform shear deformation as bainitic ferrite lath grows, twins in bainitic ferritemainly are those inherited in retained austenite as BF thickens by shear mechanism in broad face.

中脊与残余奥氏体李晶是贝氏体铁素体切变共格长大时协调均匀切变形成的形变孪晶贝氏体铁素体板条内孪晶主要是其横向侧面切变增厚时残余奥氏体的遗传李晶，且孪晶面与界面台阶有对应关系。

We got alerted a couple of times while we were down south that HETs were on the way to bring us back up north because things were going to go hot again, but it was just rumors.

南下的途中我们不只一次得到警告说重型装备运输车将拉着我们重新北上，因为局势正在变得重新紧张起来，但这只是谣传。

It's the one where they find the ghost in the salt mine.

这一集是演他们在盐矿找到鬼