查询词典 adjusting screw

Valve plate and valve seat sealing surface for the oblique cone structure, oblique cone surface in the valve plate welding temperature, corrosion resistant Water Control valves alloy materials; fixed in the regulation of the spring between the ring plate and the plate with the adjusting screw assembly structure.

阀板与阀座的密封面为斜圆锥结构，在阀板斜圆锥表面堆焊耐温、耐蚀合金材料；固定在调节环压板之间的弹簧与低温阀门压板上调节螺栓装配一起的结构。

Wash ink device is scraping rubber knife, ink tank, pine adjusting screw.

洗不朱不乱设刮不朱器是由橡皮刀、收不朱槽、不紧紧调度螺丝构成。

Swayig begnawing unleashmy paper paper teeth in, call the static state, to ensure the accuracy of the paper begnawing, still are counting on "" on adjusting screw to control, when swayig begnawing paper teeth rockers "" rock the block and if connecting rod in hand on the cam roller should be the minimum surface, gap 0.03 ~ 0.05mm, if less than 0.03mm or no gap is at rest time is too short or simply not still be in an inconsistent state, more likely to result in bilateral irregular misregister.

摆动咬纸牙在咬纸时，答在遨游状况下举行，以包管咬纸的不确性，遨游工夫是由&背景&上的调度螺丝来把持的，当摆动咬纸牙摆杆块与&背景&隔绝时，连杆牵手上的滚子答处于凸轮的最小背，间隙为0.03~0.05mm，如果小于0.03mm或底子操纵间隙不离表明遨游工夫太不幼或底子不离操纵遨游工夫，不兵处于不稳不退状况，较便当变成双边无法规套印禁绝的障碍。

To change the temperature of the water, loosen the Lock Nut to free the Adjusting Screw.

要改变水温，先要松开锁定螺母以放松调节螺丝。

And 6 intake valves. Tighten valve adjusting screw locknut to 27 N·m (20 lb-ft).

将气门调节螺丝防松螺母拧紧至27牛顿·米（20磅-呎）。

To adjust, loosen locknut and turn adjusting screw clockwise to increase pressure; counterclockwise to decrease.

如果要进行调节，则松开锁紧螺母，并顺时针方向旋转调节螺丝以增加压力；反时针方向降低压力。

To adjust, loosen locknut and turn adjusting screw clockwise to raise the setting; counterclockwise to lower.

如果要调节，则松开锁紧螺母，顺时针旋转调节螺丝提高设置值；逆时针旋转降低设置值。

To replace seat/stem module shut off supply, loosen locknut and back off adjusting screw.

要更换阀座/阀杆模块，先关闭供应管道，松开锁紧螺母，退出调节螺丝。

To clean strainer or replace seat/stem module shut off supply, loosen Locknut and Lock Seal and back off Adjusting Screw.

要清洗过滤器或更换阀座/阀杆模块，先关闭供应管道，松开锁紧螺母和锁紧密封，并且将调节螺丝退出。

The proper clearance setting should be at 0.04-0.1mm. The adjustment is achieved by loosening the locknut (fig.2) and turning the adjusting screw. Tighten the locknut after the adjustment is achieved. Alter the initial 1 hour adjustment, this procedure should be performed a few every 2 hours of use.

正确的汽门间隙为0.04-0.1mm之间，间隙调整螺丝被一个固定螺帽固定住，先将固定螺帽放松就可以转动间隙调整螺丝(如图2)调整后每一小时检查固定螺帽有没有松掉，每2个飞行小时检查汽门间隙。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了