查询词典 adiabatic

The dynamics process of the conical bubble sonoluminescence has been discussed based on the adiabatic process. The equations of velocity of bubble collapse, the pressure and temperature within the bubble have been achieved.

在绝热压缩模型的基础上，详细讨论了圆锥泡声致发光中气泡运动的动力学过程，得到了气泡塌陷速度方程、气泡内压强方程以及温度方程。

It is pointed out that the heat capacity of a polytropic process is not certainly a constant, and that the adiabatic process can not be regarded as a special case of polytropic process.

状态方程为 p Vn=c。定义 2 [4 ] 理想的等温过程、绝热过程都是难以实现的。气体状态变化时，总是和外界进行部分热交换，实际过程介于上述两个理想过程之间。

Atmosphere during an adiabatic process.

绝热大气过程的若干性质。

Several special finite element techniques, such as the chip separation criteria, friction model, heat conduction and adiabatic shear during cutting process have been implemented to improve the accuracy and efficiency of the finite element simulation.

利用该有限元模型分析了钛合金铣削加工中切削力和切削温度的周期变化规律，建立了切削力和切削温度曲线。

When the equivalent strain rate is relatively low, this influence can be neglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

When the equivalent strain rate is relatively low, this influence can beneglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

According to the engineering thermodynamic theory,the inflating work and ebulliency work exerted by the materials composed of liquid,vapour and gas during the adiabatic process are calculated.

运用工程热力学的理论计算组成物料的各气体、汽体、液体于绝热过程中对外所作的膨胀功、爆沸功。

Based on the early works, the C program language and the least square method were used to obtain the thermal viscoplastic constitutive equation.A mechanical thermal coupled model was created and DEFORM-2D was used to analyze the thermal and mechanical parameters' changing during the process of adiabatic shearing.

我们在所作的前期工作及国内外的研究成果的基础上，应用C语言程序实现了最小二乘法拟合热一粘塑性本构方程中待定参数的求解过程；在此基础上应用DEFORM 2D 有限元分析系统对，Ti-6A1-4V绝热剪切过程中的热一力变化历史进行了分析；在数值模拟结果的基础上，进行了再结晶动力学的分析与计算。

It is assumed that it is adiabatic compression during start-up process before the atmophere pressure in flow passage rise to relief pressure, the thermodynamic equation, momentum equation and rigid water hammer theroy have been applied for the analysis and calculation the variation law of air during this transient process.

假设流道内气体未达虹吸驼峰顶处真空破坏阀排气压力前的起动过渡过程处于绝热压缩状态，运用能量方程结合动量方程和刚性水击理论，计算分析出了流道中的气体压力在起动过渡过程中的变化规律。

We investigate the dynamical stability of a dark state of the atom-heteronuclear-trimer conversion system in a stimulated Raman adiabatic passage process.

孟少英 中国工程物理研究院北京研究生部，北京 100088；辽宁大学物理学院，沈阳 110036吴炜辽宁大学物理学院，沈阳 110036

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。