查询词典 addendum circle

It is the micro-external gear pump that the key component of the system, which the speed may reach 3,700 Rpm, the instantaneous pressure may reach 35 MPa as well as the addendum circle diameter only has 14 mm.

系统中的心脏和动力源就是微型外啮合齿轮泵，它的转速可达3700 Rpm，瞬时工作压力可达35 MPa，其中齿轮的齿顶圆直径只有14 mm，同时它也是影响该系统合格率的重要部件之一。

When the powder loading was fixed as 58%,the molded compact of a gearwheel whose addendum circle diameter is 700 μm was obtained with well shape retention.

3μm的羰基铁粉和石蜡基热塑性粘结剂体系，当粉末的装载量为58%时，获得了形状良好的齿顶圆直径为700μm的微型齿轮注射生坯。

Overseas low-pressure gear pump gear often used square structure,水力控制阀, that is the tooth width is equal to addendum circle diameter.

国外低压齿轮泵的齿轮常采用方形结构，即齿轮的齿宽等于齿顶圆直径。

The addendum circle is shown in thick lines, and the dedendum circle in thin ones.

齿顶线画粗实线、齿根线画细实线，啮合区不画齿顶线和齿根线。

This thesis discusses the following. First, we use the condition of inference and the concept of wildhabor cone to design the addendum circle. Second, we use TCA technique to obtain the relationship between the slip track and the angle of action, which then leads to the calculation of contact ratios. We can then design the tooth face width and the numbers of teeth based on contact ratios.

本文一开始先对空间渐开线齿轮之齿冠圆范围使用齿轮干涉条件与Phillips提出的Wildhabor Cone进行设定，再利用Litvin提出的齿面接触分析方法，得到空间渐开线齿轮对在啮合过程中作用角与滑动轨迹之间的关系，藉由此关系可以建立一套设计流程来调整齿面宽以及齿数等参数，使其能符合设计需求。

The spiral angle of graduated circle was rough estimated by measuring the addendum circle diameter and modified on milling machine.

介绍了精确测绘单一斜齿圆柱齿轮齿形参数的简便方法，即测量公法线长度计算基圆齿距从而查表确定模数和压力角；测量齿顶圆直径估算分度圆螺旋角，用分度头在铣床上修正分度圆螺旋角，并进行误差分析。

Pitch circle diameter: d = mz = 3X12 = 36 Tooth crown heights: ha = m (f0 + x)= 3X (l +0.5)= 4.5 Tooth High: hf = m (f0 + cx)= 3X (l +0.25-0.5)= 2.25 Tooth full height: h = ha + hf = 4.5 +2.25 = 6.75 Addendum circle Chemical pumps diameter: Da = d +2 ha = 36 +2 X4.5 = 45 Fixed string tooth thickness: Sxn = m (π/ 2 * cos2a + xsin2a)= 3X (1.387 +0.6428 X0.5)= 5.125 Fixed string of high gear tooth thickness measurement: hxn = m (π/ 8 * sin2a + xsin2a)= 3X (0.7476X0.117X0.5)= 2.42 Modulus coefficient x0.5 m3 O20 ° pressure angle tooth thickness Sxn5.12 fixed string Addendum Coefficient string f1 fixed gear tooth thickness measurement most high hxn2.42 Teeth z12 2, shaft wear and tear maintenance: Axis gear pump wear is mainly because with the support roller shaft at both ends between the friction and wear, so that smaller shaft diameter.

分度圆直径：d=mz=3X12=36 齿顶高：ha=m（f0+x）=3X（l+0.5）=4.5 齿根高：hf=m（f0+c-x）=3X（l+0.25-0.5）=2.25 齿全高：h=ha+hf=4.5+2.25=6.75 齿顶圆直径：Da=d+2ha=36+2X4.5=45 固定弦齿厚：Sxn=m（π/2*cos2a+xsin2a）=3X（1.387+0.6428X0.5）=5.125 固定弦齿厚测量用齿高：hxn=m（π/8*sin2a+xsin2a）=3X（0.7476X0.117X0.5）=2.42 模数m3变位系数x0.5 齿形角o20°固定弦齿厚Sxn5.12 齿顶高系数f1固定弦齿厚测最齿高hxn2.42 齿数z12 2、轴的磨损维修：齿轮泵中轴的磨损主要是因为轴两端与支撑滚针间的摩擦磨损，使轴径变小。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了