查询词典 abel summation method

Via generalizing the Cauchy method we obtain a new method,called the modified Cauchy method.By means of this method we establish two bilateral _3ψ_3 and _4ψ_4 series summation formulae,two four-term summation and transformation formulae for unilateral _3φ_2-series and bilateral _3ψ_3-series,and two five-term summation and transformation formulae for unilateral _3φ_2-series and bilateral _3φ_3-series,which contain many known results as their special cases,such as non-terminating q-Saalschütz summation formula,Bilateral _6ψ_6 series summation formula of Bailey,non-terminating Watson transformation formula and some transformations of _3φ_2-series etc.

通过对Cauchy方法的推广，我们得到修正的Cauchy方法，采用这个方法分别得到两个双边的_3ψ_3和_4ψ_4基本超几何级数的求和公式、单边_3φ_~(2-)级数和双边_3ψ_(3~-)级数的两个四项求和变换公式和两个五项求和变换公式，它们包括许多已有的结果为特例，如非终止的q-Saalschütz求和公式、Bailey的very-well-poised双边级数_6ψ_6求和公式、非终止的Watson变换公式和一些关于单边_3φ_(2~-)级数的变换公式等。

Firstly,by the analysis of influencing factors of settlement of loessal foundation, results indicated that among the three settlement methods such as the layer-wise summation method based on chord modulus, the layer-wise summation method based on modulus of compressibility and the layer-wise summation method based on modulus of deformation and so on, the layer-wise summation method based on chord modulus is superior to the other two methods and is very close to the actual measurement settlement of building according to the grey incidence analysis on influencing factors of settlement.

本文采用灰色系统理论中的关联分析法对黄土地基变形进行了因素关联分析，并取得一些成果。通过分析影响黄土压缩变形的因素，对于沉降变形因素的关联分析，在对影响变形的诸因素进行分析的基础上，最终证明选择了四种因素作为确定弦线模量表依据的正确性，证明了据此建立的以弦线模量为基础的变形定量分析的表达式是可行的。从关联分析以及弦线模量法的简便、直观、便于推广应用的特点来看，弦线模量法计算沉降是值得大力推广的。

These results show that:(1) the results retrieved from the Abel integral and absolute TEC inversion are consistent on the whole at higher orbits altitude (~800 km), and in good agreement with those measured by ionosondes; the results retrieved from absolute TEC inversion are in better agreement with those obtained from ionosondes than that by the Abel integral inversion at lower orbits attitude (~500 km);(2) the maximal electron density N m from absolute TEC inversion is closer to N mF2 from ionosondes than that from Abel integral inversion, and the method of the former is more rigorous and effective than that of the latter;(3) absolute TEC is more sensitive to cycle slip than Abel integral, but for the two ways significant loss of inversion precision due to cycle slip always exists.

结果表明：（1）在较高轨道高度（约800 km），Abel积分与绝对TEC方法的反演结果基本一致，都与电离层测高仪反演结果符合良好；在较低轨道高度（约500 km），绝对TEC反演精度优于Abel积分反演精度；（2）绝对TEC反演的最大电子密度 N m较Abel积分法获得的结果更接近于电离层测高获得的峰值电子密度 N mF2，绝对TEC反演法更加严密和有效；（3）周跳对绝对TEC反演结果的影响较Abel积分反演结果的影响更为敏感，但无论哪种方法，周跳对反演精度都造成严重损失。

The primary studying works and characteristics:1 To summarize reinforcing theory of cement mixing pile composite foundation2 To analyze the primary mechanics characters and changing rules of cement mixing pile, based on analysis of test data both indoor and outdoor.3 To discuss siding frictional resistance, ending resistance, ultimate bearing capacity of simple mixing pile and effectiveness factor of grouped piles, loading ratio of soil between piles under cushion cap of grouped piles and stress ratio of pile and soil and so on, and use many computation method and experimentation method to ensure bearing capacity of mixing piles composite foundation.4 To point out and analyze eight sides flaws and problems of the bearing capacity calculation method of mixing pile compositefoundation which ensured by national and normative method/ formula.5 To apply test results of loading tests and a few settlement observation data, use gray theory to predicate ultimate bearing capacity of deep mixing piles, actual example demonstrate engaging between theoretical predicted value and actual value.6 To apply groovy layerwise summation method to discuss entity piles method, double foundation method, equivalent layerwise summation method and consolidation theoretical method and so on, especially by combination of engineering example, use FEM to calculate or discuss the settlement and changing rules of composite foundation.7 To discuss problems of critical length of composite foundation by combination of engineering example and numerical analysis method, and analyze the contrast of critical length between simple pile load and most area load of composite foundation, not only critical length of composite foundation is relative to modulus ratio between piles and soil, but also upside load distribution area of composite foundation.

主要的研究工作与特色为：(1)总结了水泥搅拌桩复合地基的加固原理；(2)在对室内外试验资料进行统计分析的基础上，系统分析了搅拌桩水泥土的主要力学特性及其变化规律；(3)探讨了搅拌单桩的侧摩阻力、端阻力、极限承载力及群桩效率系数、群桩承台下桩间土荷载分担比及桩土应力比等，提出用多种计算方法并结合试验方法来综合确定搅拌桩复合地基的承载力；(4)明确指出和分析了按国家有关规范的方法确定搅拌桩复合地基承载力所存在的八个方面的缺陷与问题；(5)利用过去没有加载至破坏阶段的载荷试验成果和较少的沉降观测数据，尝试了用灰色理论预测深层搅拌桩的极限承载力，实例表明理论预测值与实测值吻合较好；(6)在常规分层总和法的基础上，探讨了复合地基沉降计算的实体墩基法、双层地基法、等效作用分层总和法、固结理论法等，特别是结合工程实例，用有限元数值计算等方法计算和讨论了搅拌桩复合地基的沉降及其变化规律；(7)结合工程实例，用数值分析方法探讨了复合地基临界桩长的问题，指出和分析了单桩荷载下的临界桩长与复合地基大面积荷载下的临界桩长存在很大的差别，复合地基的临界桩长不仅与桩土模量比有关，而且与复合地基上部荷载分布面积有关。

The main content of this thesis is to find and prove some summation and transformation formulae of basic hypergeometric series by the modified Cauchy method,operator method and inversion techniques,which include many well-known results as special cases,for example,q-Saalschiitz summation formula,Baileys _6ψ_6 summation formula,non-terminating Watson transformation formula and Rogers-Ramanujan identities etc.

本文的主要内容是利用修正的Cauchy方法、算子方法和组合反演技巧来发现和证明一些基本超几何级数求和公式和变换公式，其中包含一些著名的公式，如q-Saalschüz求和公式、Bailey的_6ψ_6求和公式和非终止的Watson变换公式等作为其特殊情况。

Summation of infinite series is part of the process of learning more difficult to grasp the progression part, this article summarizes the common summation of several infinite series method, as has the use of progression and the definition of sum, the use of itemized points or one differential sum, the use of split-phase elimination method of summation methods, and problem-solving steps in detail.

无穷级数的求和部分是学生学习级数过程中较难掌握的部分，本文归纳了常见的几种无穷级数的求和方法，像有利用级数和的定义求和、利用逐项积分或逐项微分法求和、利用裂项相消法求和等方法，并提出了详细的解题步骤。

This paper presents synthetic detecting fault feeder method based on the method of summation of mutual integral of transient current for intermittent arc earth fault and the method of summation of admittance mutual difference and fused current method for steady earth fault.

提出了基于电弧接地故障的暂态电流互积求和选线法和针对稳态接地故障的导纳互差求和选线法和融合电流选线法的综合选线方法。

Main points of the thesis are as follows:(1) The main function models and information relations between these models in the CAPP system in the integrated CAD/CAM project are explained, a new process plan design method is mentioned based on analyses of process plan design. This method is based on the process plan prototype, and develops the prototype little by little until the perfect process plan is completed, the prospect of this method is discussed;(2) The feature abstracting rules and methods are studied, a feature coding system is developed based on GT, all the defined feature models are described by the mathematical methods;(3) The integrated method of CAD/CAPP based on features is mentioned, this method defines a feature exchanging model, and develops an interface software to exchange design data into technology data base, this technology data base includes the design and technology information of the parts;(4) The process plan reasoning method based on features is created, this method uses Mycin algorithm to solve the reasoning of the feature process plan. A process plan making system is developed. In this system part process plan is made by the semi-intelligent method, this method uses the feature reasoning, feature process chain searching and man-computer talking together;(5) The main structure of the HOPE system is introduced, a shaft drawing and its process plan made by this system are shown, the data process problem in process drawing making is also discussed;(6) A new method of describing process rule is introduced, this method uses IfThen rules and neural nets weight values together to describe process rules, the BP algorithm is adopted in this method;(7) The optimal machining sequence problem of the process steps on the same fixturing is discussed, optimal algorithms SA is applied to solve this problem, the result shows that this method is more efficient than the traditional method;(8) All jobs in the thesis are summarized. In order to carry out the research in the future, some rational proposals are given.

全文论述的内容主要有下列几个方面：(1)较为系统地阐述了CAD／CAM一体化工程项目中CAPP系统的主要功能模块及其信息流程，在分析工艺设计过程的基础上，提出了基于特征原型的渐进式工艺设计方法，并探讨了该方法的应用前景；(2)研究了零件特征提取的原则和方法，在成组技术的基础上，开发了一套基于特征的分类编码系统，并在提取零件特征的基础上，定义了零件特征的数据模型，开发了基于轴类零件特征的参数化设计系统；(3)研究了基于特征的CAD／CAPP集成的方法，通过定义零件特征数据模型的存储结构，开发了将设计数据转换到工艺数据库中的接口程序，为后续的CAPP系统提供必要的零件形状和工艺信息；(4)研究了基于特征的工艺推理方法，将Mycin算法应用到工艺决策中，开发了基于特征的工艺推理及工艺方案生成系统，在系统中综合运用特征推理、特征加工工艺链查询及人机对话相结合的半智能化方法确定零件加工工艺；(5)介绍了整个HOPE系统的总体结构，通过运行HOPE系统绘出了一轴类零件的零件图，并生成了该零件的加工工艺方案，初步探讨了基于特征的工序图生成技术中数据处理问题；(6)研究了工艺设计过程中知识如何有效表示的问题，提出了将显式的IF-THEN规则表示与隐式神经网络权值表示相结合的工艺知识表示方法，并利用BP算法进行了工艺知识表示的初步研究；(7)研究了工艺设计过程中同一安装下工步优化排序问题，利用神经网络中基于模拟退火的理论来解决该工步优化排序问题，实践证明该方法较传统的算法具有更高的效率；(8)总结了本文所进行的研究工作，为今后进一步开展工作提出了较为合理的建议。

Abel Tasman阿贝尔·塔斯曼:Abel Tasman was the first European to reach New Zealand.

阿贝尔·塔斯曼是第一个考察新西兰的欧洲人。1642年，来到了新西兰的南岛。

In memory of Abel, the Abel prize was set up on the occasion of the bicentenary of his birth.

为了纪念阿贝尔的贡献，挪威政府在阿贝尔诞生200周年的2002年设立阿贝尔奖。

The shaping method of noncircular part and the tool holder's radial motion characters in noncircular turning process are discussed in detail in the thesis.

论文详细研究了非圆零件的成型方法和加工过程中刀架的径向运动规律。

I have not really liked him,I do not like his this kind of disposition.

我没有真的喜欢他，我不喜欢他的这种性格。