查询词典 Young modulus

In this article, three kinds of prealloy powder were developed by water atomization method. The base attribute, pattern, phase composition, differential thermal analysis of powder were researched. Sintered density, hardness, bend strength, Young's modulus were researched as hot pressed sintering temperature changing. By using abrasive wearing equipment upbuilt by the authors, the wear resistance were determined. Green-pressing density, simulated green-pressing strength and bonding momental of high frequency brazing were assayed. SEM corrosion structure and SEM appearance of fracture were observed.

本文采用水雾化法开发了三种预合金代钴粉末：对粉末的基本属性、形貌，粉末的相组成，粉末的差热性进行了分析研究；测定了它们的烧结密度、硬度、抗弯强度、弹性模量随热压烧结温度变化的规律；采用作者自行建立的磨料磨损试验方法，测定了它们的质量磨损百分率；测定了它们的冷压生坯密度、模拟生坯强度以及高频钎焊的结合力矩；观察了热压烧结SEM腐蚀组织和SEM断口形貌。

The results show that the mechanical properties of this PMMA depend strongly on the testing temperature. The Young's modulus and flow stress were found to decrease with increasing temperature at low strain rate. At the strain rate of 10^(-1) 1/s, strain soften was observed under all experiment temperatures. At high strain rate, with the temperature increase, the flow stress deceases remarkably while the failure strain increases, and the strain softening was also observed at the temperature above 333K.

试验结果表明：在准静态载荷下，随着温度的升高，材料的弹性模量和流动应力减小，在应变率为10^(-1) 1/s时表现出明显的应变软化行为；在高应变率(550 1/s)下，随着温度的升高，材料的流动应力逐渐减小而破坏应变增大，当温度超过333K时也有应变软化现象发生；在相同温度下，随着应变率的升高，材料的流动应力增大，但破坏应变减小。

The longer treatment time of samples would result in the more reduction of compressive strength and Young's modulus,because the shale or clay in rock sample would get soft by the drilling fluid filling.

岩石矿物中的泥质黏土矿物遇到钻井滤液后产生软化效应，致使岩样呈现：经钻井液处理时间越长，其抗压强度和弹性模量下降越多的趋势。

By analyzing the transverse force of test sample, a general formula has been established between the sample's deflection angle and its Young's modulus.

中文摘要：通过对测试试件的横向受力分析，建立了试件偏转角度与试件杨氏模量之间的一般表达式。

The result demonstrates that, the young's modulus and unit weight of concrete, pipe friction coefficient and deviation factor of prestressed reinforcement have large influence on the displacement of structure though influencing stress seldom, which can be chosen as the main design parameters of construction control accordingly.

参数敏感性分析表明：混凝土的弹模、容重、预应力筋的管道摩阻系数和偏差系数对结构位移影响较大，对应力的影响较小，可作为连续刚构梁桥施工控制中的主要设计参数。

Diamond has many outstanding physical, chemical, optical, mechanical, and electrical properties such as the highest thermal conductivity, the extreme chemical inertness, the highest known hardness, the lowest compressibility of known material, high in Young's modulus, low in friction coefficient, wide in band gap, and a wide optical transparency bandwidth.

中文摘要钻石拥有许多优异的物理、化学、光学、力学与电学特性，例如它拥有最高的热传导系数、具化学惰性、具有最高硬度、高杨氏系数与低摩擦系数、具有宽能隙与宽的光学穿透频域。

In the present study, the effect of centrifugal force was investigated by three dimensional finite element analyses; the vibration characters of random mistuned blade-disc were also being investigated by probability methods and the Young's modulus of material of all blades are regarded as random parameters.

结果表明，离心力对失调叶片轮盘系统局部化振动有减弱作用；所有叶片弹性模量在5%误差范围的随机失调系统，其固有频率与非失调相差很小，即失调叶片—轮盘系统可以按照循环对称结构进行模态分析。

XRD and EDS analysis indicate that at static condition, the composition of the scale is CO3, while the scale changes to CO3 at dynamic conditions. The increment in flow rate increased the thickness of the scale remarkably, but had little influence on the hardness and Young's modulus of the scale. The fracture toughness of the scale exhibited the lowest value at the flow rate of 0.5 m/s whereas the adhesion strength increased with increasing the flow rate.

结果表明，静态条件下形成的腐蚀产物膜的主要成分为CO3，动态条件下的主要成分为CO3；介质的流动能够促进腐蚀产物膜的形成，但对膜的硬度以及杨氏模量影响不大；腐蚀产物膜的断裂韧性随着流速的增大先下降后上升，流动状态下内层腐蚀产物膜的致密性较好，膜与基体的结合强度较高。

An equal cross-section blade was investigated and a finite element model was built parametrically. Geometrical parameters (such as length, width and thickness), material parameters (such as young's modulus and density) and speed of blade were considered as input random variables while the static frequencies and dynamic frequencies were output random variables. Combining the finite element method, response surface method and Monte Carlo method, the statistical properties and cumulative distribution functions of static frequencies and dynamic frequencies were obtained. Probability sensitivities analysis, which combined the slope of the gradient and the width of the scatter range of the random input variables, was applied to quantitatively evaluate the sensitivities of static frequencies and dynamic frequencies with respect to the random variables. The Scatter plots of structural responses with respect to the random input variables were illustrated how to adjust the values of the static frequencies and dynamic frequencies by changing input random variables.

文中以某试验台用汽轮机等直叶片为研究对象，考虑几何参数、材料参数和转速的随机性，通过有限元参数化建模，将确定性有限元方法、响应面方法和Monte-Carlo模拟法相结合，从而获得了叶片静频、动频的统计特性和累积分布函数；同时考虑随机变量的梯度和离散范围对静、动频的影响，通过概率敏感性分析，定量地判断出叶片静、动频对随机输入变量的敏感性；通过绘制叶片静、动频与输入变量的散点图，定量地分析了如何改变随机变量以调整静、动频率的方法。

The study shows that the effect of Young's modulus is largest, then hardening coefficient, initial yielding stress, hardening exponent and anisotropy r0 . While the effects of anisotropies r4 5 and r9 0 variation can be ignored.

研究结果表明，杨氏模量的波动对板料回弹量的影响最大，其次分别为硬化系数、初始屈服应力、硬化指数及各向异性系数r0的波动，而各向异性系数r4 5及r9 0的波动对板料回弹量的影响可忽略，且数值模拟分析材料参数对板料回弹量的影响趋势与理论分析一致。

Finally, according to market conditions and market products this article paper analyzes the trends in the development of camera technology, and designs a color night vision camera.

最后根据市场情况和市面上产品的情况分析了摄像机技术的发展趋势，并设计了一款彩色夜视摄像机。

Only person height weeds and the fierce looks stone idles were there.

只有半人深的荒草和龇牙咧嘴的神像。