查询词典 X-rated

Two-way from the X-Y table driven precision CNC workpiece completed X, 2 Y direction of the movement to X, Y, Z direction of the 3 Feed Movement ball screw, by AC servo motor drive.

由X-Y双向精密数控工作台带动工件完成X， Y两个方向的进给运动；X， Y， Z三个方向的进给运动均滚珠丝杠，并由交流伺服电机驱动。

Bar frame section 14 x 5mm black bar, 12 x 3mm for top braces, bottom angles 12 x 12 x 3mm.

酒吧帧第14 x 5mm的黑条，12，底部角度12 × 12 × 3mm的上方括号x 3mm的。

The results of its 1D test demonstrate that the MARED code is suitable for simulating implosions on different devices and with a wide range of load parameters. Combination of the wire-array Z-pinch experiment simulation and analysis shows that under the same load conditions, the X-ray radiation power produced by the tungsten wire-array implosion is much greater than the power generated by the aluminum wire array. With the same load current, the greater load mass gains the lower X-ray power.

结合丝阵Z箍缩实验的数值模拟和分析表明：相同负载质量条件下，钨丝阵内爆产生的X光辐射功率远大于铝丝阵产生的X光功率；相同负载电流条件下，负载质量越大，计算得到X光功率越低；X光功率随着负载电流增加而增加。

Scanning electron microscopy,X-ray fluorescence spectroscopy,X-ray diffraction and X-ray photoelectron spectroscopy were used to analyze the microstructure,chemical composition,crystalline structure and compound constitute of the corrosion scale from cast iron pipe and galvanized steel pipe in drinking water distribution systems.

使用扫描电镜、X荧光光谱分析、X射线衍射分析以及X光电子能谱对给水管网中铸铁管和镀锌钢管上的管内壁腐蚀管垢进行微观形态、化学组成、晶体结构和化合物构成等物理化学特征分析。

Especially the colossal magnetoresistance manganates La1-xCaxMnO3 , one of interesting materials in our lab, exhibited strongly CAPO at various doping concentrations (x=0, x=0.3 and x=0.58). However, several mechanisms about the generation and detection of CAPO have been proposed and disputed each other.

特别是在本实验室感兴趣的La1-xCaxMnO3庞磁阻材料，在几个掺钙含量x=0、x=0.3、x=0.58，也都呈现明显的同调声子振荡，虽然形成同调声子振荡的机制有几种不同的理论模型，但互相仍有所争议。

When the thickness of ITO was 210 nm, the Alq3 based TOLED exhibited a narrowed Electroluminescent peak at 536 nm with a full width at half maximum of 22 nm, of (0.229, 0.729) and an efficiency of 1.77cd/A. 2. With Alq:DCJTB/TBADN:TBPe/Alq:C545 as white light-emitting layer, RBG tricolor TOLEDS were achieved by adjusting the thickness of ITO. We obtained the peak wavelengths at 603nm, 475nm and 538nm, CIE coordinates of (x=0.513, y=0.360),(x=0.133, y=0.201) and (x=0.335, y=0.567), FWHMs of70nm, 30nm and 48nm for red, blue and green, respectively.

以多层结构Alq：DCJTB/TBADN：TBPe/Alq：C545为白光发光层，通过调节ITO的厚度，实现了红、蓝、绿三基色发光的顶发射微腔器件；当ITO的厚度分别为240nm、180nm、215nm时，器件发光峰值为603nm、475nm、538nm时，色坐标为(X=0.513，y=0.360)、(x=0.133，y=0.201)和(x=0.335，y=0.567)，半高宽为70nm、30nm、48nm。

If the pregnancy is absolutely can not do X films, X-ray radiation on the human body does have a certain damage, the extent and severity of damage to receive X-ray exposure dose and the relevant parts.

如果怀孕了是绝对不能做X片的，X线照射对人体是有一定损害的，损害的轻重程度与接受X线照射的剂量和部位有关。

It applies the Fourierism-Gauss spectrum analysis on the in-situ X-ray instrument and advances the precision and the area of in-situ X radiation sampling technique.

本文的研究是对现场X荧光分析技术的一项补充，将原本在微机上使用解谱技术应用到现场X荧光分析中，提高X荧光的测量精度，扩大X荧光的应用范围。

Thus plasma expansion's effect of primary disk on secondary disk is reduced,and then the X ray radiation ablating secondary disk is "pure and clear".An X ray streak camera is used to measure time space images of double disk targets.

采用X光条纹相机测量双盘靶等离子体喷射的时空扫描图象，采用两台软X光谱仪分别对初级和次级辐射的X光进行测量，研究次级盘对初级发射的X光谱的改造。

And shape by using X-ray to penetrate the log . The absorb of X-ray between log internal defect and log internal xylem is different .so the X-ray photograph is different .If we can get the several side X-ray photograph of log .and input the photograph into computer to digital image process . Then we can get the data and the location of log internal defect .

由于原木木质部分与内部缺陷部分对X射线的吸收能力不同，在X射线底片上形成的影像也不一样，如果对检测原木从不同的方向进行照射，再把得到的射线底片输入至计算机内部进行处理，就可以得到原木内部的大致空间结构参数，对原木的加工有重要的辅助作用。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐