查询词典 W

Finally, it was indicated about the advantages of the W/O/W multiple emulsions with encapsulation efficiency, penetrating ability, and stability to resist acid pH (1.2) and high temperature (60°C).

由本次试验证实，W/O/W 乳化液可促进 rhG-CSF 於肠道黏膜细胞的穿透率、耐酸性、耐高温及包覆率的效果，并且对小鼠的肠道组织不会造成损害。

In order to explore the influence of the bath composition on Ni-W-P alloy coating structure and properties, to find the right ratio, so as to lay the foundation for follow-up experiments, SEM/EDS, X-ray diffraction, and metallographic analysis and other methods were adopted to study the composition and structure of different chemical deposition of Ni-W-P alloy. And the hardness of different components of the sediment layers plated state and the hardness after heat treatment were measured.

为了探索镀液组分对Ni-W-P合金镀层结构与性能的影响规律，寻求合适的镀液配比，为后续实验莫定基础，采用扫描电镜／包谱、X射线衍射以及金相分析等方法，研究了不同成分和结构的化学沉积Ni-W-P合金层，测量了不同成分沉积层的镀态与热处理后的硬度。

In the development of reduction clearing agent, first we selected several surfactants according to the capacity of removing the oligomers and good emulsification, then mixed these activators and obtained washing agent W. Mixing the agent H and washing agent W, the reductive clearing agent WS was acquired.

在还原清洗剂的研制中，以分散性好、对低聚物有去除作用以及良好的乳化能力为基准，选取了几种表面活性剂，然后对选取的表面活性剂进行复配，得到了助洗剂W；将还原剂H与助洗剂W复配，得到了还原清洗剂WS。

Therefore,it is recommended that the optimum solid solution for cold-drawn billet is follows:(1 150±10)℃×20 min,W.C.and for cold-drawn bar:(1 080±10)℃×20 min W.C..

推荐冷拉坯和冷拉材的优化固溶工艺分别是(1 150±10)℃×20 min，W.C。和(1 080±10)℃×20 min，W.C。。

After keying in tel No. press * for three or four times . then ,show "p"or"w",input "p"or"w", then key in entension No. and press dial No.

在您键入总机号码后，连续按*键三次或四次，出现&p&或&w&触屏笔离开屏幕，输入&p&或&w&号，再键入分机号码并按拨号键。

Leslie W Russell, for appellants. W. M.Hawkins for respondents.

莱斯里 ·W·茹塞尔为上诉人辩护；W·M·豪肯斯为被上诉人辩护。

The results show that the best sintering process for SiC preform is 1100℃, 8 h in vacuum, by which the open porosity is 99.6% and the preform strength reaches 0.57MPa. The thermo-physical characteristics of 57% SiC/Al composites produced by this technique are as follows: the relative density is 98.7%; the thermal expansion coefficient is 7.5×10^(-6)℃^(-1) which almost matches those of GaAs and BeO; the thermal conductivity is 1.65×10^5W/K, which corresponds to that of Cu(15%)/W and decuples that of Kovar alloy; the density is close to that of aluminum and less than that of one fifth of Cu/W.

结果表明：经1100℃真空烧结8h的SiC预成形坯开孔率可以达到99.6%，抗压强度为0.57MPa；所制备的57%SiC/Al复合材料相对密度为98.7%，热膨胀系数为7.5×10^(-6)℃^(-1)，与GaAs、BeO的接近，热导率为1.65×10^5W/K，与传统Cu(l5%)/W相当，是柯伐合金的10倍，在密度上接近Al，不到Cu/W的1/5。

This makes Ni-W-P powder more suitable for partial hydrogenation of dienes. The kinetic results suggest there are some different between the active sites of Ni-P and Ni-W-P powder. DSC, XRD and EXAFS results suggest that the tungsten codeposition makes Ni-W-P powder more amorphous than Ni-P powder.

动力学结果表明在两种合金微粒上，不仅环戊二烯与环戊烯的相对配位能力不同，而且它们各自的反应速率常数也不一样，表明非晶态Ni-P、Ni-W-P合金微粒的催化活性中心存在着一定的差异。

The number of identifiers has in creased with each release of W in dows; the programmer's documentation in W in dows 1.0 listed only 26 of them.

这些标识符的数量随每个 W in dows 版本有所增加；W in dows 1.0 中的程序员文档只列出了它们中的 26 个。

A simple cuts method, combinedwith artificial neural network, is used to select signal. Fitted by binned maximumlikelihood method, the cross sections of single W leptonic and hadronic decaysare found to be 0.16〓±0.02 pb and 0.42± 0.12± 0.03 pb, respectively. Thetotal cross section of single W is 0.58±0.13 ±0.04 pb.

根据这些特征，我们采用简单CUTs和人工神经网络结合的方法，从大量的原始数据中挑选出单W事例，然后用最大似然函数法拟合单W轻子道和强子道的反应截面，结果分别为0.16〓士0.02pb和0.42士0.12土0.03 pb，其总截面为0.58士0.13±0.04 pb。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失