查询词典 Under Pressure

The characteristics of pressure drop of wire packing rotating packed bed absorber in air independent propulsion system are analyzed under counter-current condition and the model of pressure drop is built.

对不依赖空气动力装置系统不锈钢波纹丝网填料旋转床吸收器在气液两相逆流条件下的气相压力降特性进行了分析，建立了压力降预报理论模型。

ZSM two-drum pulse low net work of the screen, pulp pressure from the top of the screen to cut into the screen, the two fall in the middle drum sieve, sieve in the drum inside and outside of the pressure difference and the dual-rotor rotary-wing together, qualified fiber Through the inside and outside the drum screen after screen to the body at the bottom of the pool, and then by the good plasma discharge tube machine, the screen remained in the dark between the flow of rough slurry residue by the rotor and driven together to drum sieve under the tailings from the slot after the Slag discharge pipe.

ZSM双鼓式低脉冲网前筛工作时，纸浆从压力筛的上部切向进入筛体，流到两个筛鼓中间，在筛鼓内外的压力差及双旋翼转子的共同作用下，合格纤维通过内、外筛鼓后汇集到筛体底部，然后经良浆管排出机外，留在筛鼓之间的粗渣受到浆流和旋翼的推动，汇聚到筛鼓下的尾渣槽后从排渣管排出。

Secondly, to start with the distribution of temperature field, pressure field and dryness fraction along the injector well, the paper built a steam heat loss forecast model of the injector well, obtains condition the best steam injection pressure and steam injection speed under certain formation.

其次，从蒸汽沿注汽井井筒的温度场、压力场以及干度的分布入手，建立了注蒸汽井井筒的热损失计算模型，得出一定地层条件下的最佳注入压力和注汽速度。确立了井筒的最佳注汽压力和速率。

In this paper, using single-phase water as working fluid, the experimental research was performed to investigate the frictional pressure drop and heat-transfer characteristics of forced convection in narrow annuli under atmospheric pressure.

本文以单相水为工质，在常压下对窄环隙流道进行了强迫对流换热特性和阻力特性的实验研究。

Travel time in WC anvils was measured using pulse reflect method at room temperature and under cell pressure up to 3.0GPa.Experimental results indicate that the travel time in the WC anvils decreased linearly with cell pressure.

在常温、实验压力为0～3GPa条件下，利用脉冲反射法测量了纵波在碳化钨压钻中的走时，结果发现，随实验压力升高，碳化钨压砧的走时线性减少。

The digital simulation of thedynamic processes under step load input and supply oil pressure fluctuation were carried on by MATLAB. Analysis of the dynamic characteristics was done with the changes of the supply pressure, load, structural parameters of spherical hydrostatic bearing and the effective bulk modulus of oil. The conclusions show that structural parameters of the spherical bearing and the effect bulk modulus of oil have significant influence to dynamic characteristics, but the elasticity deformation of interior supporting collet has very small influences on the output response characteristics of the suspension system. The collets deformation can be neglected on the project.

在此基础上，建立了考虑内支撑筒的弹性变形与否时悬浮系统的数学模型，同时，建立了线性化的仿真模型，利用MATLAB对阶跃负载输入和油源压力脉动输入下的系统进行动态过程的数值仿真，结果表明球面副的结构参数，油液的有效体积弹性模数对系统的响应特性有明显的影响，而内支撑筒的弹性变形对悬浮系统的响应特性的影响很小，在工程上可以忽略其弹性变形。

Debriding under local anesthesia and pressure dressing are good management.Conclusion Thoroughly stopping bleeding,reliable pressure dressing and shoulder immobilization can reduce the incidence obviously of breast postoperative hemorrhage.

乳腺手术后出血重在预防，术中止血彻底，术后加压包扎可靠，适当限制患侧上肢活动可明显减少术后出血的发生率。

The computational fluid dynamics method is used to simulate numerically the two phase flow of gas and liquid in a demister with corrugated baffle. The demisting efficiency and pressure drop under various droplet diameters, gas velocities and plate spacings are provided. The effects of main design parameters on the demisting efficiency and pressure drop are analyzed.

用计算流体力学方法对波纹板除雾器内的气液两相流动进行了数值模拟，计算得到了不同液滴直径、进气速度与叶片间距下除雾器的除雾效率和压降，并分析总结了各参数对除雾效率和压降的影响规律。

During the displacement, the low adsorption methane was always first to be desorbed and the high adsorption CO2 was late to be desorbed. The displacement results under the high pressure is always better than the low pressure.

在置换过程中总是吸附能力弱的甲烷首先解吸，而吸附能力强的二氧化碳最后解吸，而且较高压力下的置换效果总比低压下的好。

The technological scheme is that under the conditions one reaction temperature 40-200 deg.c, reaction pressure from normal pressure to 6.0 MPa and reaction velocity of 0.5-3/hr, C4 mixture as the main material is made to contact with catalyst to produce isooctene. The production process may be used in industrial production of selective C4 mixture dimerizing process to prepare isooctene.

本发明通过采用以混合碳四为原料，在反应温度为40～200℃，反应压力为常压～6.0MPa，反应液体体积空速为0.5～3小时-1条件下，反应原料与催化剂接触生成异辛烯的该技术方案较好地解决了上述问题，可用于混合碳四选择性二聚制异辛烯的工业生产中。

By the time of its fall, most of the prisoners were writers who had written against the corruptions of the government.

到它被攻陷的时候，里面多数的犯人是写了反对政府贪污文章的作家。

The most obvious variation to ovum morphological character was that the color was changed from light green to sepiaceous in embryonic development, and all the ovums were almost hatched after 96h.

在胚胎发育过程中卵的形态特征最明显的变化是颜色从淡绿到深褐色，卵在发育96h后卵基本全部孵化。